Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear All,we have a UC solution deployed on a single UCS c 220 server and we need to make it redundant.do we need to have another UCS server ?what type of licenses are required for the redundancy like VMware and Cisco ?Please helpBest regardsKennedy
Hi,Looking for best practice in removing 1 of 2 VIC2-4FXO cards from a 2811 used as a VG. From the physical point of view, it would be a matter of powering down unit and safely disengaging the card. I'd like to know if this should be done before r...
I setup a call handler that transfers to user extensions fine. If the caller enters an extension number after the greeting they get transferred to the number, but if they hang up before the call is answered the recipient phone continues to ring. I am...
Good Afternoon ...I was a problem when wanting to communicate telephony between two routers 3925, on both routers and I have configured thetelephone service (telephony-service), I have discharged my phone and there are internal communication in each ...
Hii uploaded Arabic language locale file in cucm .and restrat the tftp serverin cucm .but the cisco 7945 the display is not in arabic language it showing by default english language.
Hi,I'm running CUCM 9.1. When a call arrive Cisco 9971 is not displayed the Divert option to transfer the call to voicemail manually. I have read this option is only available using Softkey but how can I add this option if Softkey on Cisco 9971 can't...
For outbound SIP Trunk calls, can we configure 1 IP Address with say 16 different port numbers using above optionThanks
Network Admin has changed DNS server IP address and now I have to do those changes in CUCM. I am running CUCM 9.1, I would like to know is it going to impact my licensing file or do I need to request new licenses?
Trying to see if anyone has seen this before. VMs were being successfully left and retrieved from a particular VM box. Yesterday over 200 VMs appeared in the mailbox with timestamps ranging from about the time an upgrade was done...
I have a VoIP Dial-Peer that I created to match a particular number and send all digits to the Call Manager. However, it is only sending the last four of the number and not the whole number. Am I missing something? Is this normal behavior?Direction f...
Hello,I am setting up a SIP integration for CUC with CUCM. When I am calling an extension internally, instead of hearing the prompt "Sorry Extension not available" I am getting the greeting of my extension " Extension 'My Extension' Enter you PIN" an...
Hello, I am facing problems with incoming calls on a MGCP PRI Gateway. Some of the incoming calls get disconnected with cause code: Cause i = 0x80AC - Requested circuit/channel not available - Destination address is non-ISDN I noticed that this happ...
Hi All,I want to configure all ports of the SM-D-72FXS inserted in a 2951 Router (MGCP) with the CCM 9.1 Bulk Administration but I can't find anything that explain me how can I configure this... In the bat file appear only tag for VGXXX...Any idea?Th...
Dear All,Will be gratefull if someone could help us in getting a solution.We have Tandberg E20 registered (as third-party device advanced) to CUCM 7.0. We are able to make calls to E20 from any SIP or SCCP Phones. But we are unable to make calls f...
Hello,I'm testing out a SIP trunk on my Cisco CME, but can't get it to authenticate correctly to the ITSP. A packet capture shows that the CME is trying to authenticate using <extension#>@1.2.3.4 but the ITSP requires <areacode+phonenumber>@1.2.3...
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
