Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,UCCX Version = 8.5.1.11003-32My Question:I have 2 Teams (Team 1 & 2 ) which use UCCX and they have a lot of Agents .Team 1 has an Event today and all Agents are out of Office today until Tomorrow.How can a Supervisor of Team 1 make a redirect ...
Dear All,I faced a very strange issue. All DNs in my CallManager have become marked as shared. Even DNs that exists only on one phone. Route Plan Report returns correct information but when I'm looking for line on every device, line is marked as shar...
Hiii ExpertsWhen the router connectvity to Server fails (via E1) ....the phone connected to switches...3905(SIP) and 6921(sccp) gets register into local srst mode within 2 minutes....but the 8945 phones are not registering itself into local SRST mode...
I need to split our company across two AD Forests and do not want to setup AD LDS for Dirsync and authentication. Can I disable LDAP synchronization on CUCM 8.5.1 and have it leave the current users objects? I would look to add passwords to each of...
Hello,I have been asked to configure 3 route patterns to send over a SIP Trunk to Responder5 Nurse Call System (Brekeke)Route Patterns:5*.XXX*XXXX#5*.XXX*XXXX*X#5*.XXX*XXXX*XXX#I have been asked to stip the information prior to the '.' and also remov...
I am trying to add a Cisco ip phone type 8945 to a CUCM version version: 7.1.5.33900-10The phone type 8945 does not show up in the drop down window in my Callmanger.I am trying to find out if i need to add the new firmware for 8945 and the device pac...
We have a remote site running a CUBE router. It has an MPLS connection back to headquarters. It also has some analog lines for SRST. It has a dedicated DID for that site, that comes in via SIP to headquarters (CUCM v8.6). When the MPLS circuit go...
Hi All,i`m i doubt that the following Sip message we are receiving from an Endpoint, connected via a Sip Trunk is right.For me it seems there are Information missing.Let me explain the traffic caseAn Attandant console is connected via a Sip Trunk at ...
I'm using the Cisco UC sizing tool for the first time (installed on my laptop)It appears that I am unable to save my design - I get an error message "XML Output file could not be opened for writing"Looking through the embedded FAQ in the Szing Tool, ...
is it possible to get live or realtime calls logs ( incoming and outgoing coming inside or outside the call manager)?
I am currently running a CME 7.1 server and yes I know there are newer versions out there I actually have one but can't utilize it until my IA does his job. This being said we have a remote site that has the 7911 phones and i am guessing they were us...
I have a gatekeeper configured as: zone prefix test-A 8....... blast gw-priority 6 us-gw1 us-gw2zone prefix test-A 8....... gw-default-priority 0zone prefix GlobalDGK-US 8.......zone prefix GlobalDGK-UK 8.......So which entry does the call (destinate...
Running CUCM 9.1 and documentations says Que status can be monitored via a PLK on select models.How do you set a PLK on a 7911? I have not seemed to find a Softkey that says Que status either.Am I missing something?ThanksKevin
internal extenson is 53XX-55XX and external line is 3670100-3670350,how can I configure translation to make PSTN Directly call internal extensions ?The Router is 2911 and line is E1.thx!
Hi guys,I have CUCM 9.1.2 and a 2901 MGCP gateway with a VWIC3-1MFT-T1E1-E1 card and am trying to integrate this with a Seimens PBX.I have been following this guide to help with the config http://www.cisco.com/en/US/solutions/collateral/ns340/ns414/n...
