IP Telephony and Phones

Resolved! CUCM 8.X Upgrade to CUCM 8.6.2.23900

Hi Support CommunityI have the following issue that we have run out of ideas for and as of yet havent got anywere with Cisco TAC. We have a CUCM cluster running 8.5.x and have upgraded to 8.6.2.23900 and we are now at the stage of introducing an addi...

CIPC 8 Install Doesn't Retain CIPC 7 Settings

I'm trying to replace CIPC 7.0.5 with CIPC 8.6.3.0. Some users are seeing their Device Name and TFTP Servers copied right over to the new version, some aren't (having to remember and retype them in manually). Any ideas what might be causing it NOT to...

Resolved! Real Time Media Resources Monitoring

Hi all,I am trying to measure Media Resources Utilization, with particular regard to the Conference Bridge.From RTMT I am able to see their general state, but not how many channels are or have been in use, which is what I am trying to find out.Anyon...

show voice port summary

Hi guys,can somebody explain what is meant by "on-hook" and "off-hook" in this output? This seems confusing, because I knew these On-hook and Off-hook states are for telephones.

CUCM Authentication on INVITE

We have a requirement to have CUCM challenge for authentication when it receives an invite from a SIP 3rd Party Device. Apparently, this functionality is available on other PBXs. How do we configure it on CUCM?Thanks!Jeff

CUCM - P-Asserted-Identity

Topology: CUCM ---- SIP ---- CUBE ---- SIP ---- SPSometimes, when I place a call, it redirects it to an internal extension. The only SIP message that I can see being sent when that happens is a 180 ringing with a p-asserted-identity in it. It only ha...

Softkey Template - Redial button not appearing

We have around 50 phones - 8941 - issue - the phones even after setting the correct call state and adding the red-dial softkey option in on-hook and off-hook template the , the 8941 phones, do not seem to show the key, even after rebooting the phone ...

Resolved! 45 mail boxes but 42 used (Unable to add another mailbox)

Hey,A client has got 45 mailbox enabled but only 42 used and when i try to add another user/mailbox it saysNot enough Mailbox space left in systemCan you please help mePlease rate the post Shibly Ibrahim

User locale on 8961 with 9.3.4

Hello,I upgrade IP Phone 8961 and 9951 from 9.3.2 to 9.3.4 and I have user locale german.Then I upgrade the user locale "po-locale-de_DE-9.3.4.1000-1.cop.sgn"In the readme is written:3.5.1 Set user locale to English (United States) and save;3.5.2 Res...

configure FAX in cme

Hi allI have cme 2921 router and 4-port FXOpossible the configure FAX in fxo port ?I need purchase FXS card or ATMmy cme version 9.0Thanks

Resolved! CUCM 9.1 CDR Reports

Dear All,I am running call manager 9.1.Is it possible that i can see the call duration of the users.Is there any option in the Call manager 9.1I want to see the call duration of called and calling party.I will be very thankful for your support.Regard...

Cisco Unified CME 10.0 on Cisco 2911

Hi Pros, I got a small project and new to Cisco IP telephony. I have a cisco router Cisco 2911 with image (c2900-universalk9-mz.SPA.152-4.M1.bin) and I want to push CME 10.0 to this router. I cannot push complete tar file as my flash memory is 14...

CUCM - 8.6.2

Hi All - Recently we have installed CUCM - 8.6.2 with PUB and SUB, After the installltion when we checked the DB Replication in CLI where it shows 2 for both PUB and SUB.When i check the GUI, It throws below Error.All necessary services are UP and R...

8961 IP Phone conference call blocking

Hi,I have an IP Telephony setup in CUCM 9.1 and having IP Phones 8961 and 6945 phones.I need to block conference facility for all the IP Phones. For 6945 SCCP phones I made through the Softkey button template changes and conference is disable for al...

t1 trunk between asterisk and cisco

hi All,i have implemented a ciscsolution running a cisco 2921router as the voice gateway to cucm 8.6.the customer has an existing legacy system in Asterisk EIC. they want us to link these two systems together, however i have never done this before.i ...

IP Telephony and Phones

Forum Posts

Resolved! CUCM 8.X Upgrade to CUCM 8.6.2.23900

CIPC 8 Install Doesn't Retain CIPC 7 Settings

Resolved! Real Time Media Resources Monitoring

show voice port summary

CUCM Authentication on INVITE

CUCM - P-Asserted-Identity

Softkey Template - Redial button not appearing

Resolved! 45 mail boxes but 42 used (Unable to add another mailbox)

User locale on 8961 with 9.3.4

configure FAX in cme

Resolved! CUCM 9.1 CDR Reports

Cisco Unified CME 10.0 on Cisco 2911

CUCM - 8.6.2

8961 IP Phone conference call blocking

t1 trunk between asterisk and cisco

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

Upload files to CUCM via SSH CUCM 12.x

Incoming calls show as forwarded

CUCM sends wrong device ID to Recording System

CDR reports: Request for activity on multiple lines

I get dozens of these alarms on WU, but no errros on controller

Cisco Jabber

IMAGICAL BILLY BLUS

CUCM CAP-RTP-001 and CAP-RTP-002

Issue with ciscocm.enable-sha512sum-2021-signing-key-v1.0.cop.sgn inst

How to setup SAML SSO authentication in Expressway C