Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello all!I have a strange situation.I have CUCM and two 2911s.First 2911 has transcoder and mtp on it. I added both of them onto my CUCM. both of them are "registered".Second 2911 has CME on it.CUCM and CME (2nd 2911) have SIP trunk between them.and...
Hi All, I have some problem with my H323 to H323 cube connection,IP Phone A ----- CM 1 - H323 --------- firewall NAT -------- H323 CM 2 ------- IP Phone Bboth of IP Phone A and B can call (ringing) each other but no audio.when i pressed ? button on m...
Hi all,Wondering if there are any ISDN experts lurking in the forums that could shed some light on which configuration is correct.At each site:We have a cisco 2901 or 2801 with a BRI card conencted to an ISDN line. 8 x Cisco 6921 IP phones,CUCMEAIM m...
i have CUCM 8.6.2 integrated with LDAP , when any changes done to any user on LDAP from active directory team then i do perform manual sync the changes don't take affect on end user page on CUCM and i have to wait to schedualed automatic sync to see ...
HiI have an update from CME to CUCM configuration , i have a solution VOIP between 14 sites using CME.I need to know best solution for VOIP . I have to upgrade my solution from CME to CUCM. I have to register all remote sites gateway as H323 to do VO...
Hi,we collect CDR from CUCM 9.1.1 to send it to a analysis software.Normally the field in CDR named origMediaTransportAddress_IP are filled with the gateway IP address if calls come from PSTN. In our case there is always 0.0.0.0 as IP address so that...
Hello All I found the following errors now being experieinced on my 2911 CME install. I'm having trouble trying to work out what is causing it. There are SIP and SCCP devices but no SIP trunks. All outbound is PSTN.I ran Debug ccsip and get the f...
Hi,I am deploying some 6945 phones with SCCP load connected to CUCM 9.1Is there a way to view stats on a call (e.g. codec, MOS etc.) similar to what 79xx phones display when you hit the Help key twice?
Hi,I have a CUCM cluster 7 connected to ISP.through SIP trunkWhen I make a outgoing call from a IP phone through SIP trunk the call is fine but if I forward the IP Phone (forward all) to a external number and I call from PSTN to that forwarded Phone,...
Hi,If we are migrating/Upgrading Cucm from 7.1 to 9.1, how will migarate the licence file to ELM ? can i use the same licence file for the new version?
Hi,I think it is not possible, but customer asked me if it is possible to download existing voicemail's from Unity express?We are going to implement e-mail notification so we will have the new voice mails in the future.But what about the old ones?Tha...
Hi!I have no audio when a call is coming through sip trunk and is forwarded on phone to other destination by CFA.I only have a Sip Trunk to make and receive external calls.No problems in normal incoming/outgoing calls through sip trunk.transcoding en...
Guys,Have a strange issue here - user logs into phone, goes into corporate directory, and inputs a search the way you normally would.Log out, and back into that same phone but this time with a UDP that has the netherlands locale, the phone resets and...
Hi, our company uses Communications Manager 8.6.2 and has a requirement which I haven't been able to fill using normal methods.We need to call 5 mobile numbers at the same time when an emergency exists at our location. Only one of the 5 called numbe...
Dear team,Today in the morning, I have faced with the issue that UCCX Engine in Partial Service on UCCX 8.0.1.10000-11.I can manage Application and Promts, Scripts.I cannot manage Resources, skills, CSQ.Yesterday I've deleted not used skills.My call ...
