Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,We recently have a new SIP circuit from telco with 200 extenstions.They had given me below detailsCustomer IP address= 192.168.1.224/30STC IP Address = 192.168.1.233/30Protocol= SIP SIP Port = 5060 Transport Protocol=UDP Voice Codec= G711 A-La...
Can anyone help on the configuration of the cisco ip 7937 conference phone? Everything is fine, excerpt I cant have three party conference. Error message appear from the phone "cannot complete conference". Thanks
Hi All, I have Issue of ONEWAY audio in SIP my HO in India and Remote Location(out of india) ,INDIA>> REMOTEREMOTE>> INDIA ON BOTH THE CALLS REMOTE LOCATION CAN HEAR US BUT WE ARE NOT ABLE TO HEAR THEM ALSO ITS SAME BEHAVIOUS VIA IPHONES AND ...
Hi all,I got some issues with incoming fax through an ATA-187 on CUCME 9.1.Is there some best practise sheets or can someone spare a setup to check the settings, supported speed e.g.Kind regards,Norbert
Hello everyone, first time here, need a little help.I'm having some trouble to find a solution to the following problem.Recently I've installed CME 9.1 using the router 2921. Most of the phones are SIPs, model 3905 (around 20 of them), with the last ...
Hello everybody. I have a network with two 2921 routers in it (K22.R1 and K22.R2), each router runs OSPF process with all networks that this router belongs to ncluding voice network), each have it's own CME (9.1), first CME works in VLAN 2 (10.10.22....
Hello All, I am running into a weird issue. We have an h323 gateway with a PRI connected to a PBX for calls between the cisco phones and Nortel phones. From most phones it works. However some phones it does not work. I even found a scenario wher...
Hi there, Just a general question here, does anyone know how the gateway in CUCM knows which CSS used for routting the outbound call?
Hello allI have a question about fxo and fxs .My lab is very simple but have some problems.################################################analog phone ==> R1-Voice-GW (FXO port 0/1/0)<=====> (FXS port 0/2/1)R2-PBX ====> analog phoneMy config setting...
Hey GuysIs there a way to swap roles between two CUCM servers in a single cluster?Pub to Sub and Sub to pubCould you just do a physical move of the VMs and then re-IP them?Any idea appreciated, cheers Mike
I have several users who want to forward their phones to other numbers if they can't/don't answer (easy), but then, if the call isn't answered at the remote destination, have the call fall back to their voicemail (the issue). Is this possible? I am u...
Can someone tell me how to turn on DTMF relay on a POTS dial peer or even in global config??? What is happening is when we make a outbound call and the call is connected, an IVR is on the line as the calling party. When the called party presses keypa...
We have created a translation pattern (6925) which allows our users to call an internal number in order for them to get routed out to their external helpdesk via the PSTN (908456016925). Initially this didnt work as the translation patter number of 6...
CUCM 8.5Xmediusfax ver 6.5MGCP GatewayCenturyLink PRISome faxes failing. It's only about 5% of the total but these are customers and I need to fix it.We had this problem early on and Xmedius tech support and Cisco TAC were able to fix most of it by c...
This is new to me, so pardon my ignorance ;-) We're in the early stages of deploying a CUCM (latest version of release 9) and I had a training class that raised a few questions and concerns. Question 1:Regarding conferencing, if we only have the CU...
