Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dears,I have a Cisco 6921 phone I registered it with CME 8.6 normally and this can display the username on it.But when I registered it with Cisco CM 9.1 the display name didn't display on the screen.Please any ideas for this issue,Regards, ...
I think I allready post on that and I got different answer somewhere else..Anyone did a CUCM migration from 5K to 6K We know for the unity we can user the Cobra but for the CUCM I think we cannot do a CUCM backup and Restore from DRS because the pla...
Dear Friends,We are planning to implement the IPT on one of our customer, we are planning the below design but need some expert advise on this.IP Phone (In India) -------> CUCM (In USA) ---->Gateway (In USA) to PSTN (USA).No PSTN calls to India would...
Hello. I have a problem.No ouside outgoing calls go((( To call outside we use SIP server. But it shuts our calls because it goes from private call numbers! In debug I see:VOICE_REG_POOL: No entry found in contact table Sent: INVITE sip:0444555146@77....
Hello evereyone! Thanks in advanced for looking.We have a CISCO 2901 router configured with DMVPN and IP CISCO phones 7945 that is part of our WAN. We have 4 digit calling across the VoiceNetwork on 3 different states (using Call Manager) We recently...
I have created separate dial-peers for inbound and outbound calls on th same voice-port (FXS) and I am not sure why a particular dial-peer is being match on the inbound call. If you look at my configuration below, a call is coming in from port 0/2/0 ...
Dears,I got a issue on Publisher and I can´t get ccmadmin by browser; I restart the Publisher- Cluster CUCM, 1 Publisher , 2 Subscriber- CUCM 5.1.3.2000-3 - BD Replication is GoodServerNumber of Replicates CreatedReplicate_State10.108.55.5 ...
Hi,we are planning to connect our cucm in europe with the cucm in USA.We need to look at new dial plan.US suggests to start *1XXXXX to dial internally from EU to USA. eg, *198765We suggests to start 82XXXXX to dial internally from EU to USA. eg, 8219...
Hii, I want to buy a Conference kit for the meetings rooms and I need some opinion about the models, in the past I used 7937 and now I want to by 8831 and I want to know your ideas about this conference kit ( is k or not, how many license.... ).I u...
Hi All,Webapps folder is missing in this path C:\ProgramFiles\wfavvid\tomcat_appadmin\ and I am not able to login to the appadmin webpage.Please suggest what needs to be done.UCCX version is 7ThanksBhavna
Hi,I have a two sites configured with the following:Site A:DevicePool_A (No Local Route Group Set)Specific Patterns with Specific Route listDevice & Line CSS approach (Gateway at Device level and Blocking at line level)Site B:DevicePool_B (Local Rout...
Dear forum users. CUCM Cluster:- System version: 8.6.2.22900-99971 Active Load:- sip9971.9-3-2SR1-1A very simple problem. If you are using a PC connected to the PC port of a 9971, and you disable the NIC of the connected PC, the audio stream of the ...
Greetings!Could you please give a piece of advice on the following issue?When you initially add a contact to your contact list everything works fine: there's a clickable phone button in the highlighted contact. But after some time (for example after ...
HiDoes anybody knows how to do priority to a hunt pilot agains others? I want to configure a hunt pilot with a pool of users waiting to call and other hunt pilot for vip users.In the test i did in my mock-up in the hunt pilot 196 for users and hunt p...
I have recently been tasked to trace a phone call where an inbound call to our help desk was transferred to a customer that was curently on the phone with our help desk. I pulled the CDR report and Found Inbound caller (A) was forwarded to an externa...
