Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a gate phone with an analog POTS line. It interfaces to our router via a MGCP FXO port with attendant DN pointing to a shared line.When users call from the gate, the called party's phone shows (Unknown Number).I would like to disable this fro...
Hello,I'm stuck trying to solve a problem with one-way audio. There is a following diagram: subscriber (DN 3318) - PBX - BRI - 2801 (IP 172.25.0.30) - SIP trunk - UCM 8.6 (IP 10.7.81.65) - 7961 IP phone (DN 1001, IP 10.1.12.16). If I call 3318 from 1...
Hi,Show controllers E1 output shows around 30 slips for 15 minutes interval. Is this the acceptable slip rate ? Some PSTN calls are getting dropped, unable to understand where the problem is. Apart from this slip rate all other counts are zero. Pleas...
Hi Support,I have installed CUCM/CUC 6000 (UCS C200 M2) Exsi.4.1.0 i use ova taplates for both now i need to install the .lic which MAC should i chose i didnt understand do i have to configure manually this is the network output for CUCM what if i r...
Hello All,We are trying to figure out the phone numbers associated to the POTS lines on our 1800/2800 Series Router/Gateways. I know the easiest way would probably be to just remove the phone line from the back of the router and plug it into a plain ...
Hi,We have a situation where fxo ports stuck in off-hook state. I have to do a shut /no shut in order for fxo ports to come back to normal. The same situation occurs after 24h up to 48h. We have CME 7.1 on Cisco 2811 Router and below is the fxo port ...
Hi,I am configuring a CME 7.1 system to which both SCCP and SIP phones are registered - the SIP phones are DECT cordess phones but are seen as 7960 phones as CME.When I make a call from a SIP phone to an SCCP phone the call works but when I then try ...
Hi all,I need your suggession for adding site code for existing number.There are 40 sites in our cluster and some sites are not configured with site code.We are facing some issues with internal dialing and voice mail creation for overlaping extension...
Cisco IP Phone 7962 remains in "Upgrading" state | CUCM 8.6==================================================Hi team.I execute a "factory reset" to Cisco IP Phone 7962 because the phone could not register. (Please view 7962_1.jpg).The issue is that h...
HiFor Fixed Mobile Convergence feature usage; what type of license is required?Is it Standard or even supported on Foundation?
Hi,I'm trying to integrate cue with cucm but i'm having some issues.I've sessioned in to the cue configured the appropiate parameters.I am able to get to the GUI of the cue and after i hit "run initialization wizard"I have the possibility to fill in ...
Hi,Hope you are all fine.I want to know how I can proceed to make a Billing Of Material for the products on the Subject of the forum?The solution must be virtualized.So I dont know how I can make this BOM.What are the part numbers I can use in order ...
Does anyone know of 3rd party phones for CUCM that can handle features like extension mobility and phone services?
Hi allI would like to get jabber working on my call manager for my iphonesI cannot see any software under device defaults for thisdo I need to download any cop files for this? if so where are the ones for cucm 8.6 ?cheersCarl
I'm having a little difficulty designing our SIP VoIP network.I currently have my Cisco Voice Gateway Router with CUBE licensing accepting SIP calls in Florida and my Call Manager and majority of my users are also Florida.We just opened a 20 man offi...
