Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello.I have currently configured a PRI and BRI line on a 2921.I need to configure another PRI line on a separace 1-port T1 VWIC(same telco provder but separate DID), and have the phones configured for that line to be separate from other lines (incom...
HI NetPro I have a CUCME running sccp and sip phones, and i have a sip provider to PSTN, in the CUCME i have a configured HW transcoding and works fine for PSTN calls from to sccp phones.Here my problem, the PSTN accept only G711 and my SIP client it...
Hi All,We are facing the huge delay in the IP Phone firmware upgradtion. It took 30 mins for 6 phones. Phones & TFTP Server in the LAN only.CUCM - 8.6.2Phone : 69XXFirmware : 9.2.2.6Is there any new changes in the Firmware update. i didn't experianc...
This must be a matter of some option at ephone-dn level, but I cant seem to find which one When a user receives another call while having a current one, she hears beeps in the headset informing her of another call, which is okay. However, after three...
Hi All,One of our clients has the requirement to connect a IP SIP trunk to the gateway. Currently we use only PRI/ FXO/FXS for PSTN access. They provided the SIP provider's IP address and credentials. I read that for any IP to IP gateway connection, ...
I have installed CUCM 9 cluster and it is working fine but i dont know how to configure Extension mobility in cluster.Please give your inputs.Im not using DNS In my network.Without using DNS how we achieve Extension Mobility Failover
Hi i'm goign to update unity connection 8.6.1 to 9.1, Unity Connection 8.6.1 is running on Virtual Machie (EXSi 4.1), when I'm instralling 8.6.1 I used OVA template for 8.6, for Unity Connction 9.1 these is an another OVA, so can we upgrade 8.6.1 to ...
while browsing the servecibility page and then open CDR reporting i get the error in tha attachment screen ,and after close this warning the CDR work normal , any one can advise please ?
Hi All, we have to CME systems one is using a 2911 ISR running CME and a UC540 running CME. They are not interconnected.I'm looking in setting up Mobility/SNR on each system however, I'm not clear on the call flow. So if a call comes from the PSTN a...
Hi Guys,we have 4 ephones dn(s) ,two of them associated with ephones,but the othe 2 ephone dn(s) are not associated with ephones and under their configurations there are call forward all commands configured to mobile network,so the call comes on any ...
During a recent install, one of our customers snapped the wire to the Cisco Microphone 20. Can this cable be easily replaced in the field? Or does this need to come back to Cisco for repair? If it can be replaced in the field, what is the replacement...
Hi Friends,Getting call manager alert Interface USB status is down..can any one explain about this alert,purpose, how to troubleshoot...Regards,Prashant
Hi everybody, I have problem on PSTN call to Ex60Here is the environment - T1 connection to Voice Gateway- Voice gateway 2811- CUCM 8.6- IP phones 7970 (DN: 1001)- EX60 (DN: 1001)- DN 1001 sharelineTested success:- All internal calls are working fin...
hello everyone,I'm starting to learn Cisco VoIP. How do I block call forwarding outside of my organization? I have CUCM 9.0. Thanks
I know 7.1 is not supported on vmware but I am only doing this to clean up some device/line settings before moving them to my new cluster thats built.Issue is everytime the cucm 7.1 pub in vmware tries to get the dma file it says there is not patch f...
