Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,we have a customer with a 8.51 CUCM (8.5.1.13900-5) and all their 6941 phones are one hour ahead of time. All their 7900 phones have the correct time (Timezone Europe/Amsterdam). They only have one Date/Time group for the whole system. It looks li...
Hi Community,Hope every one is well...i am having a issue with couple of new cisco 7945 CCM 6.1....iam getting ip phone registration error with db config error....i have tried everythinhg cisco and guys on google recomended apart from reeboting sub a...
Hello to all , I need to create some translation patterns for emergency calls arround the country , the problem is I MUST use the same number ( 888 , for e.g ) for all the translations , just look :Rosario , disc 888 forward to 11441522Jujuy , disc ...
Hi,I have got a cisco 2811 router. Accidently I have erased the Flash file. Now when I reboot the router,the router does not get me anywhere.I am connected to it via the console and all I get on the screen is a few funny characters?If anyone can help...
Hello guys!I am experiencing the following behaviour with a CUCM 9.1.1a routing calls to PSTN through a h323 gateway Cisco 2921: The CUCM has a route group for Route Patterns with first option a SIP Trunk on the gateway and as seco...
We're running UCCX 7.0 (1)SR02_Build099. Roughly a week ago our end users reported they were unable to login to CAD. Upon checking the servers the event viewer was showing several error messages as below... Event Type: Information Event Source: LDAPM...
Hi,Need help on how to interpret the IOS of CME. Currently, the Cisco 3925 is ruuning CME version 9. However, I am lost to understand the IOS version:IOS Version: 15.2(0.13.4)PIA17In Cisco's website, it says that the CME version 9 should have an IOS ...
I Guys,I read any documentations, but, not stayed clear for me if the IP 7940/7960 with SCCP accept or no encryption. If not accept, is there any documentation?Thanks,Wilson
Hi,Put at the time of summer too much rate for IP-Phone.But not everything the all Ip-Phone.I check the NTP server and it's OK !Thank you for you help.
Hican any body provide visio stencils UCS-C210M2 for call manger server
HelloI am upgrading from the 8.6.2 (a) to 9.1 is it possible???, Is it i am uploading a correct file as per the attached.I m getting the error Name does not match any filter pattern please have a look in the attached fileThanks
Hi Everyone,I am having an issue with setting up a new CUCMBE6K deployment with UCCX inclusive. We have a CUCM 8.6 and UCCX 8.5 and we can get scripts and queueing working and so on.The problem is that when we "hold" calls in the script there is no M...
hi allwe have EX60 TE6 and MCU 4505 (SW4.2)both are registered with CUCM 8.6.(2a) when we try to intiate ad-hoc video conference from EX60 to 9971 with camera using MCU as conference bridge the call retried as audio conference call.i checked the web ...
Hello all,We are running Cisco 6945 with SCCP on Asterisk. Phone is registered and can call out as well as receive calls.However it is not possible to set Remote-Party ID or CalledParty ID on outgoing calls, this works fine on Cisco 7911 and 7945.Als...
Hello folk!I’ve faced the strange behavior of ip sla over ipsec.We have remote office (cisco 891) connected to hub (asa 5520) via EzVPN. This tunnel almost uses for VoIP traffic so we need to monitor quality. There is the following Ip sla on 10.10.1....
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
