Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi I need to modify some SIP headers, bellow is current SIP header message From: "ABC" <sip:26469@172.25.X.X>;tag=300668~aeff0cc2-52d4-4da3-8c9f-b147ebe7c734-42429702I need to change this as following From: "ABC" <sip:117416000@172.25.X.X>;tag=300668...
Hello,I am having 2800 series router equipped with two PVDM2-64 cards and two different PRIs are working. Now i want to know how many simultaneous calls (Incoming & Outgoing) can be handled, if both PRI's are active. Router's image feature set is SPS...
Hello,I have a problem with configuring the CUCME 8.6 (Cisco 2911/K9) with the SPA303 IP phone. In our company, we have several IP phones (CP-6921), which are configured and registered via SCCP and everything work perfectly. However, we have several...
I have installed CUCM 8.5.1.10000-26 OS in Cluster but when I want to add IP phone 8941, I cannot see phone from the list in Add options so do I need to do upgrade patch or just installed the Phone firmware on servers. I am looking to further any as...
We have CUCM 8.5.1.13900-5 and have an issue with MOH files. We are able to uploaded these fine on the PUB and SUB servers within the cluster. They go through the trancoding process and complete OK. We setup the MOH source pointing to the new file...
Hello,Have a simple questions about setting up express on a lab router. We have an assorted mix of 38xx, 29xx and 39xx series to test with, but wanted to get a feel for the interface and cmd line a bit in a lab eviorment. With the 12.4 versions pha...
Hello Cisco Professionals! Thank you very much for your time in advance, the solutions here have helped me tremendously.My issue is with the Agent Desktop Supervisor SoftwareThe regular Agent Desktop is working fine, allowing users to log in as neede...
Hi all.Good Morning.Please, could you help me with a problem.?I am currenty using Unity Con 8, call handler for Auto attendart. And I want now to after the greeting is finished (just one time), It rings to the operator extension.I already see many op...
Hello I want to know if there is a way to limit access to the TFTP server of the CUCM or apply security to deliver the files that the ip phones needs but onlyto the ip phones or CIPC not to other type of device such as a computer.Im asking this becau...
Hello, I am new to the forum and am hoping someone can answer this.I have seen this post before with a suggested workaround is to use SCCP firmware 8.4. This I did try and I can get SRST to work with SCCP 8.4 (phone registers and has correct DN it ha...
Can someone tell me the right place to verify that a Voice Feature card with DSP modules is compatible with the new IOS upgrade that was recently completed on this Voice Gateway. It is a AS5350XM. We upgraded to 12.4.23 IOS.ThanksBrian
Here is my setup (lab environment, not production)2 x analog phones, 1111 and 2222.Connected to FXS ports on PBX (2811)Also on PBX are two more FXS ports (3333 and 4444). Each of these lines are tied to FXO ports on the local side CUCME. On each...
Does Call Manager 4 support Time of Day routing as i do not see any option.As i have requirement US Extension (US Cluster) will have a configuration on the call manager like this: If anytime Customer calls at that number, it will ring on every phone ...
Maybe due to carrier, some of our FX0 calls don't disconnect (the situation occurs most when call originates from outside and outside hangs up first; especially more likely when the outside caller was on hold or in conference and th...
Phone un-registers when I type "switchport access vlan 205" I have both 7965s and non-Cisco devices I need on vlan 205. Phone load is SCCP45.9-2-3S2960S-VOICE-02#show run int gig1/0/1Building configuration...Current configuration : 363 bytes!interfa...
