Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello all! I'm new to voice so be easy on me I have a brand new installation of CUCM7 on ESX5 with 6 7961 IP phones. I'm going through the process of setting up and I can web gui into the CUCM. I even turned on the some of the services like Call mana...
We have a new Cisco CME 9.1 in one of our international offices that's displaying the incorrect time on the 9951 phone sets. I went to telephony-servcies>time-zone +240 but the time on the display did not readjust even after restar...
Hi All !! Hope everyone is doing well !!!I have a 3825 router with a few FXO ports and a couple TollFree numbers point to them. The 3825 router is configured as H323 gateway with CUCM 7.1.3 and the POTS lines are set up in a huntgroup. What I am tryi...
Hi,I have tried to upgrade MCS-7825H3 from 6.1.4 to 8.6.2a multiple times and failed. It gives different failure messages at times. The latest error says that "Unable to find a valid USB drive" and upgrade fails. I have attached a valid USB device (1...
When we migrated out of version 6.x to 8.6, dial tone behavior changed. Prior to the migration, there was no secondary dial tone. After the migration, secondary dial tone occured after you dialed a 9 for an outside line. So, [press speaker button]...
I have an issue where the SCCP StopTone message is sent to phones immediately after a SIP 183 is received on the SIP trunk. I also get a SCCP StopTone at the correct location when the call is answered.Phone in the US calls a UK number. This is rout...
Hi guys!!! I'm installing a CUCM 9 and I'm making some tests and I have an issue. If I receive an external call and make a blind transfer to another extension if that person does not answer the call does not came back to the originator. I run all the...
Does BE6000 supports Vsphere 5.0?RegardsLeonardo Santana
Hello,I have an issue to use Calling party transformation rules for call forwarding.I work on CUCM 8.6.2.20000-2 and I have a SIP trunk configured like this:- Outbound - Called Party Transformation CSS: "CSS_CUBE_Outbound_Called"- Outbound - Use Devi...
Hi all,I have been trying to make SIP calls from my Cisco 5300 RTR terminate to my ISP ( TATA) but still can’t get it to work call are getting disconnected after first Ring. Below are the equipment Involve. E0 ...
Hi,We are on the Cisco UCSS workspace licensing track.My understanding is that the only licenses for users are Standard and Professional licenses.However, I have just seen a license called the CUWL-entry.Does anyone know anything about this type of l...
HiI am facing issue of incoming call is landing on gateway, but its not going to cisco ip phone in Sip srst mode.Show Running deb isdn q931sh voice regist t allBuilding configuration...Current configuration : 3405 bytes!! Last configuration change ...
Hi,I have an environment with two CallManagers in a cluster (Publisher 192.168.96.10 and Subscriber 192.168.96.11) and a 2851 as MGCP gateway. All the devices using as primary CallManager the Subscriber and registered to it. The MGCP gateway can't re...
My customer's requirement is quite simple:- during office hours, send the call to a hunt group- during non-office hours, send the call to a CUE Voice Mail Box (or play an announcement, should this not be possible).My understanding is that this is not...
Throwing this out here in case someone has come across this particular issue one of my sites is experiencing.Had 3-4 reports over the past days of phones, that after a call will not hang up. Only a blank grey window shows on the display. Using the ...
