Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,i have on Router 2901 is working as a PSTN Gateway with MGCP to UCM 8.6.2. All it's working fine. But i cannot enter the connand:mgcp package-capability srtpdt-ccm-sbhkw-vgw-001(config)#mgcp package-capability ? as-package Select the Anno...
Hello all,Has anybody managed to successfully setup Oreka for call recording (BIB, CUCM8.5). I see SIP INVITE sent to Oreka server (with Wireshark), but the server is sending ICMP 590 Destination unreachable(port unreachable). I think CUCM side is fi...
Hi Everyone, I've been struggling with this for a while now, gave up on the h323 connectivity and went back to SIP. Here is the scenario: We have a Cisco Unified Communication Manager 6.1 system in one office, which is up and running and working fi...
Dear All,I have installed Cisco unity connection 8.6 and integrated with CUCM 8.6.Now I need to integrate Cisco unity connection with Microsoft Exchange 2010 SP 2.Kindly let me know· -what will be the initial steps to perform this task· ...
I recently setup a CME9.1 longest-idle hunt-group with four 9951 SIP phones, how to make each phone logout of het hunt-group ? Alternatively , it will be OK if there is any softkey / feature-buttion can busyout individual phone ?Pl...
Hi all!I have a problem in a router 3925. IOS (Version 15.0(1)M2) This router have two PVDM-3 64, on the motherboard.The hardware recognizes PVDMs.###################################################################################################VGW-...
I am running a single site deployment with CUCM ver 8.0(2) Pub/Sub. We have all phones in one Voice VLAN using three LAN switches and VTP to distribute the VLAN across the LAN. All phones are programmed with the same Device Pool. There is only one ...
SRST 9.1CUCM 8.6We have set 74 phones enable in CUCM to register in SRST, however only 7 phones got registered while in SRST.Any ideas from where to start checking?Thx,
I have cucm 7.1.3 , i want to do DMA backup on it , and I have tried many times but unfortunately give me error : remote file " DMAExportSuccessful03-12-13#18-02" does not exist or cannot readremote server name or ip : 192.168.50.1 remote file path :...
Hello All, we have a server that answers calls and gives out info. Our call flow is as such:PSTN--- PRI ---- Cisco 2911( h.323/SIP) ----- CUCM 4.x ---- Server (Gateway)Customers call a specific number via a specific dial peer to the server. Sporadica...
Dear Team,E1 channels and T38 protocol gets disabled automatically and Srst is not working .I want to upgrade IOS,please send me the link to download the IOS one of the following .I am unable to fine these in download? 15.1(24.6.12)PIL13,15.1(1.7.1...
Hi All,I got requirement from client to install 6921 on CUCM 6.1 , but 6921 is not supported on CUCM 6.1.Is there any alternate solution to register it!!!!!!!!!Thanks in advance!!
DearsI have some issue in Transfer call,when call center agent transfer the calls its going hanging 10 time a day. we have to much load of calls transfers. using CM 6.1 with one Cluster phones are hanging for 20 sec at that time we cannot do any thin...
Hi,I have a scenario in which we have 3 AA and one queue. Now each AA has its own operator groups. Can there be some configuration that takes them to their respective operator group when '0' is pressed?Currently, I am able to configure only one opera...
I have a scenario wherein the user has connected an USB Hub ( Make : HP 3005 PR Port Replicator) to the IP Phone. The USB Hub has 2 ports of USB 2.02 Ports of USB 3.01 Ethernet cable to connect to the Network1 Headphone port 1 Micorphone port1 Displa...
