Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi There,We have a small branch that have several IP phones, we installed the phones and they could register to the CUCM 7 without problem.But later on, we did factory reset for the phones and they were not able to get the new firmware installed.Als...
Hi,We are using Cisco business Edition 3000 server We would like to configure Cisco IP Softphone & ip communicater in desktops. Is it required any licence for server? other wise how we can configure please guide us.Thanks,Narsimha
Hi everybody.Please consider the following scenario:analogphone1--------- voice port0/0/0---Voice gateway.-voiceport 0/0/1--------analogphone2Router#voice-port 0/0/0Router(config-voiceport)#caller-id enableRouter(config-voiceport)#station-id number 6...
Hi every body. I have few question about CUCM ver 8.0Cisco Unified Communications Manager Version 8.0 Supported platforms:• Cisco MCS 7800 Series Media Convergence Servers, including the Cisco MCS 7816, MCS 7825, MCS 7828, MCS 7835, and MCS 7845 • S...
Hi everybody.I am trying to understand when we need dial peers . My focus is only voip dial peers right now.Case 1:ipphone1-----sw-----CME---sw---router--Wan---router----sw----ipphone2.Both ipphones are registered with CME. Since both are registered ...
Hi,I am trying to upgrade CUCM 4.2.3 to CUCM 7.1.5. I have taken the back up using BARS and exported using DMA. Now when I am trying to validate the exported data, it fails. I did this 2 times and both the times it was a failure. Please let me know w...
Guys,just wanted to get some general input on a sceanrio we have had two instances of the following and we are wondering if there is something we are missingQTY 1 UCS C210 at "HQ" and the other QTY 1 C210 at "DR SiteSites linked by 10 to 15 MB links ...
Having issues with the BACD script, albeit a wierd error.When I call "751" from a local softphone on the CME, the menu/script works without issues.However when I call from an external phone, I dont hear the menu, and the call disconnects after 15 sec...
I have CUCM 8.6 and a H.323 gateway with VIC2-2BRI-NT/TE.I'm thinking about connecting ISDN phones to the CUCM using the VIC2 in NT mode.I was looking for configuration examples but didn't found anything usable...Any hints ?
Hi guys,I have one cluster with 6 subscribers, i am trying to add one more server which is 7835I2-K9-CMC1, i checked in CISCO matrix the server is supported for production at least you have to upgrade the memory to be 4GB and min HD 147 GB, when i am...
Hi everybodyI am looking for some a good link on auto registration feature of cme. thanks and have a great weekend.
Cisco 2901 VoIP router with PVDM3-16= module, PVDM3-64= module, VWIC3-1MFT-T1/E1 card. IOS 15.1(4)M4We are replacing our 1760 router with this new 2901 router and the configs are the same. When we dial out we here a busy tone and sometimes when dia...
Hi everybodyPlease consider the following set up. (201.201.201.1)Ipphone1(201.201.201.11)--------CME------------------------ipphone2(201.201.201.12)Our design requires ipphone1 to use co...
Hi evey body.ipphone(201.201.201.11)--------sw----CME----SW---ipphone2(201.201.201.12)A ip phone ( 201.201.201.11) calls ip phone2 ( 201.201.201.12)A CME sends a open receive channel message to calling ip phone ( 201.201.201.11) as show below:No. ...
Hi,I'm hoping someone can help me with the following solution.I have 2 PBX's for redundancy and 2 SIP trunks. If the SIP Provider fails on the primary SIP and will automatically send the incoming calls down the 2nd trunk. but the issue i have is that...
