Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Greetings,We are trying to install CIPC 8.6.2 using MSI using the below.msiexec /i CiscoIPCommunicatorSetup.msi TFTP1=172.17.1.2 TFTP2=172.17.1.3 FREEFORMDEVICENAME=%extension% /qb- reboot=reallysuppressThe installer isn't creating the TFTP values in...
Guys,I have the follow problem with one onf my customers.She has the remote destination feature configured and enabled for her mobile and desk phone.When she receives call it rings first in her desk phone and after that it goes to her mobile, if her ...
I am on CM 8.6 and trying to do a bulk task that would change settings button access from enabled to restricted as i dont like end user to be able to see anything except user prefernces,i am pretty sure i have done this kind of change using BAT on pr...
Hello.Each time my phone doesnt aswer call directed to huntpilot number it auto logouts from Hunt Group. How can I disable this behaviour because it is very annoying for me. (No HLog softkey configured)regardsMat
Hello.Each time my phone doesnt aswer call directed to huntpilot number it auto logouts from Hunt Group. How can I disable this behaviour because it is very annoying for me. (No HLog softkey configured)regardsMat
Hello firends , i dont have much experience on Cisco voip, i only a bigner in this area and i need to ur help to reslove this ,..plz..I am running in CME v8 environment , ...After factory resetting using the 123456789*0# sequence the phone sat in th...
Hi,I have a 2811 which I inted to insert a VWIC2-2MFT-T1/E1 module on it and create trunks with a Panasonic TDA600 pbx. The extension card on Panasonic is PRI30.I need the router to translate channels on this trunk to SIP. A SIP trunk will be made be...
Hi Everybody,I have a CUCM8.6 and a H.323 VGIn VG, I defined the ----------------------------------------------!sccp local GigabitEthernet0/0sccp ccm 192.168.1.1 identifier 1 version 7.0+sccp !sccp ccm group 1 associate ccm 1 priority 1 associate p...
Hi allI configured extension mobility on cisco call manager express but i dont know how to configure it so my user's can set their passwords individualy like it hapens in call manager environments where at the time of log out user have an option of "...
I have 2 PRI's from 2 different service provider. Both are sending last 4 digits of the DID as DNIS. Co-incidently both are sending 1369 as DNIS for 2 different DID's.How can we configure the dial-peer so the call gets routed differently for both the...
I have a customer that currently has CME on a 3800 series router.I am proposing two options to get them a little more current.a)Add more memory to the router and I can upgrade them to 8.6 CME/CUE and that is it.orb) Replace the 3800 with a 3900, move...
I wanted to know if anybody has a sample config for a PUB and SUB solution. I am trying to design one for 300 voice mail user along with a UCCX Call center for 25 users. I was looking at the C210-M2 but I needed some advice.
Yesterday our phones failed over from primary to secordary then back to primary server. Now, features like Call Forward and voicemail indicator are not working from the phones. Does anyone have any suggestions as to how to fix this? Is it a database ...
CUCM System parameter Block off net to off net transfer controls Trunk to trunk transfer. But this is system level, is it possible to control this at a user level.
Hi ,I have a problem during upgrade process for unityconnection cluster from version 8.5.1 to 8.6.2 .I installed on both of the servers (Pub&Sub) the ciscocm.refresh_upgrade_v1.1.cop.sgn and then I insert the Installation CD to the CDrom of the serve...
