Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HI there, we have following policy map applied to ingress of one of our router LAN interface (connected to internal network), can someone explain how to interpreter the last line in the blue? thanks... Class-map: Restrict-To-T...
Hello,We are relatively new to the world of Cisco, recently having installed an ISDN30 line with CME 8.6. I have managed to get gw-accounting to log to FTP successfully, however the log files contain far too much information for what we need.It is a ...
Hi all, tried to reduce the inline power from 12.0 W to 6.3W for cisco IP phone 7965, it works fine and save a bit electricity, but does this might have any nagtive impact on the phone? also is it OK to connect 7965/45 to class2 s...
Hi Edson,Greetings!We have a serious problem with our IPphones incoming calls, the callers are trying to reach us and the calls are hitting the boardline but not getting transfered with the respective extensions. This is hapening very frequently. Kin...
Hi there,We need to order a CallManager Express (ISR 2901) for a sales office in Shanghai. Which BRI/or PRI VIC are support over there?Thanks a lot.Greets,Norbert
HiI'm running a cluster of CUCM 8.6. I'm looking for a report that can show the MOH audio source used by each device. (It will be nice to see the Dependency Records in the MOH Audio Sources web page, but there is no such page)The reason for this is b...
HiI have a Cisco 7936 that was homed on a V4 ccm and is happy at cmterm-7936-sccp.3-3-20.bin, i know need to move the phone to a V8 ccm and upgrade to cmterm-7936-sccp.3-3-21.cop.sgnIssue is the phone is unable to find the correct TFTP file, looking ...
When our phone system was originally setup the vendor never added voicemail into the CUPC software. I have since migrated us over to jabber and finally had some time to setup the voicemail settings. I have tested it on myself and a few other users an...
I have to physically move a Callmanager subscriber and would like to know how best to shut it down with minimum impact. The cluster is running 8.0.3. I know we can just shut down the server via the cli but was hoping we could do this in a more contro...
Even though I've been back and forth through the configuration settings, I can't get MOH to work, all I get is tone on hold.Anyone experienced the same, and solved it?The CUCM configuration, by the way, was started by importing from a CUCM-BE.upgrade...
Dear i have issue in MOH its not working at all i upload the file and each configuration its ok Transcoder is Register with GWMRG-Software is not taking the ip Phones. all services is restarted even CUCM is restart and its working on VMWear.
I have a simple UC remote site with 4 POTS lines. At night, they forward the main line to an answering service (from the phone, call forward all).The call rings to the router with clear ringback, but as soon as it forwards the sound quality is extre...
1) Does anyone know how to configure unity to prompt callers that their Outlook Inbox is full?2) Caller A calls caller B internally and leave a voice message but caller A outlook inbox is full. Can caller B receive caller A voice message in this case...
My client has a handful of users using Single Number Reach but they're reporting that when receiving calls via Unified Mobility Caller ID is showing the main number of the facility where they're located, rather than the (original) Calling Party numbe...
Hi Gents,This is a good one for all you troubleshooters.....IP Phone A calls IP Phone B, signaling is established and IP Phone B rings. However, when IP Phone B is picked up the call is dropped and IP Phone A receives a fast busy signal (beep...beep)...
