Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello, anyone knows if it is now supported or we still need cisco servers under vmware?Sent from Cisco Technical Support iPad App
If one user puts a caller in Call Park and another user puts a caller in Call Park and only one number is assigned for Call Park, how do you know what caller you are getting when you try to pick up the caller from the Call Park?
Hi, I have a CISCO IP PHONE 7945 . I did a factory defaults reset using this tutorial: http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtmlThe problem is that after the reset, i get the "Upgrading" screen as de...
Hello everyone,I have "possibly strange" request from client (never had to do it since now, so don't know if it's even possible) : Is it possible to configure UC 500 as a voice gateway and have it registered to CUCM 8.6 as voice gateway.They have CUC...
We are looking for Unicast MoH support on CME with 3925 Router, Can you please suggest configuartion details.
Is it possible to configure VG202 from the network for the first time.Requirement is not to connect console cable even for first time configuration.Is it possible to get VG202 in DHCP mode from factory the way IP phones comes in.
We have an existing v6 CUCM cluster with a number of C2821 gareways who are running IOS c2800nm-ipvoicek9-mz.151-4.M4.bin.One of these gwy's has 2 ISDN BRI ports: VIC2-2BRI-NT/TE.On the V6 CUCM both ports register correctly and work without problems....
Hi All,I am facing a problem for registering CIPC to CUCM using Aventail VPN Client. I can register CIPC locally. After connect using Aventail VPN Client to my network i m able to ping the CUCM server. But unable to register CIPC to CUCM.I have tried...
Hello Everyone,I have an anooy problem with ATA 187 on CME 9.0I preconfigure everything back in the office, at that time ATA 187 work fine with CME - "show voice register pool type ata-187" show that both number were registered to CME. But for some r...
when we connect pc to Ip phone on the pc port computer is geting 160. Ip address and I pphone is working good but not computer.when we connect computer to same port it is working fine.interface GigabitEthernet2/0/17switchport access vlan 2switchport ...
Lets say I have 3 T1 PRI coming in from the PSTN, not an nfas group. I want to route all outbound calls to the PSTN. How to I group the 3 PRIs into 1 logical link?
Hi There,I have a demo environment of CUCM 8,0 installed on a vm mechince with only 30 IP Phones runnning.I have a post by Jamie Valencia for changing the admin password for GUI CUCM.I have access to the CLI of the server,I have tried the command set...
Hi,I have CME 2921 and Slim IP door Phone, I want to configure IP door phone to be integration with CME, anyone know what is the correct configuration which I have to apply it on cme.regards
for the life of me I can't get this dial-peer to match so I can route fax to email. I've attached the relavant config areas. I need to make it so that when someone dials into the line 4801234567 it matches dial-peer 7. It always grabs dial-peer 8 and...
Currently I have a UC540 setup with call blast to all users. A secretary picks up the phone and transfers the calls accordingly. All calls operate perfectly never going to a fax tone or anything like that.I'd like to setup an autoattendant however wh...
