Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Morning, Gens.Maybe someone has such experience!I have a cluster Pub + 2 Sub's. The currecnt ver 6.1.4.2190-3. I'm planning to migrate to ver 8.6 ( for Russia i supose UNRESTRICTED)Is anyone has such experience ? I will be appreciate for any usefull...
Is there a way to look at the outbound call history in RTMT through call manager? I have a third party automated system that is connected to CUCM via a SIP trunk that I need to look at the logs to verify what happened to the call. The automated syste...
Hi All,We have a CUCM 8.0 with more than 300 users, and our PSTN voice gateway configured with H323. Outgoing and Incoming Calls are working fine,Now we had purchased new 2 servers with CUCM 8.6, For testing- connected to the network for testing PSTN...
Hi there,This is my question, it might not make much sense, but I'm asking anyway..I have 2801 running CME 7.0 it works well so far been running for about a month, with all inbound outbound calls work flawless, knock on wood ..The router is also used...
Hi,I use Cisco 7961 in SIP version with headset. How to configure phone to automatically answer calls but only when the Handset is active (only when the HEADSET LED is green). At this moment, the phone automaticly answer a call on the Speaker too. B...
Hello guys! The DRS webpage is not loading (it goes blank) after logging in on the CUCM 8.5. I read there is bug CSCtq18270 that have something to dpo with it but, is there a fix. I need to configure backup but unable since the page goes blank.
Can I upgrade directly from 6.1.3 to 8.6, or is there an previous upgrade I need to do?..Thaks,José Valderrama
Hi All,I am very new to Cisco webex connect, I am creating this descussion just to increase my knowledge. Having the following questions.1. Normally contacts and meetings options are availabe in cisco webex connect window, how to bring phone option a...
Hi, I have 2 questions here. 1) Anyone has successfully upgrade from 6.1.x to 8.6.x directly using the bridge upgrade approach? 2) I have the below older MCS servers available for the above upgrade but Cisco recommended 4GB RAM and 160Gb ...
Hello Folks,Is there any way where i can get the information about the last accessed date in cisco unity connection, since i could see only the last password change time.Your answer is much appricated.Thanks,Kuls.
i am looking for info on setting up inbound fax to mail i setup we have is:CUCM 8.6Unity 8.6 2921 routersThanks
Is it possible to remove system greeting (i.e. Leave your message after the tone. Finnaly hang up or press # for more option) or rewrite it?Calling users confuse, then hear two almost same greetings with different voices.Thanx in advance!
Hi all,I currently make my thoughts about the things which happens during the switch version process of the Publisher.So what I tested is I switch the version on the Pub (8.0.3 -> 8.5.) and after the Pub was back online with all services, all telepho...
Hi All,Anyone here familiar with CUCM CTI? We've a voice recording application that used CTI for recording user's phone call. however on and off without any reason we found that the recording will fail if the LineStatus in RTMT CTI Search is having s...
Hi..I've been scanning and reading through the cisco website and specs for 2 hours now, but can't seem to find the answers I seek.I'm asked to see whether one can replace a Panasonic IP Phone System with a Cisco solution.. I'm quite sure that one can...
| User | Count |
|---|---|
| 14 | |
| 9 | |
| 7 | |
| 4 | |
| 1 |
.jpg "VIP Expert"){kind=icon}
