Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi AllI have a client that want to use CUBE to sit between two CUCM clusters because they have overlapping IP address. Has anyone heard of this before or know of a better way to deal with this situation? If someone done this before can they share a...
Good day!Can anyone support me in configuring SCCP client (Cisco IP Comminocation) at home with my CME 2901?CCME has an interface with public IP (routing and etc is configured already), i can establish ssh session without any problem.Will such connec...
Hi all,I am experimenting in our lab with using ENUM lookup and a CUBE (3845 with IOS 15.1(3)T3).I have followed the document posted on the Cisco example configuration website: http://www.cisco.com/en/US/products/sw/voicesw/ps5640/p...
Hello All,I am currently trying to investigate and collaborate the required procedures to upgrade a call manager business edition CMBE 8.x server to a fully integrated Call Manager (CUCM) solution 8.x or 9.0, in particular relating to licence transfe...
Hi guys…Is there any way that anyone can think of to provide the ability to call forward a shared line on a handset without using the CM User page?I.e. 7942 with Line 1 as their personal line and the line 2 as shared line. At present, pressing the ca...
Is there a way from within CUCM (8.6.2) to change the Left Softkey on the Line View page to default to Ph Book rather than Messages?The only way I know of now is to change this setting from the phone itself under 'Phone Settings' > 'Customize Home Pa...
helloi have Cisco UCS-C200M2 server with one electric supplier i need to know if it safe to add one more without turn off the server i dont want any damage heretkshoham
hay i install cucm manager 8.6 on ucs serveri configure on the cucm manager software conference bridge (not hardware on gateway)when i operate the meet me feature, only 4 calls can access to the room the fifth call recive annunciator who play that no...
Hi,I am using the NM-1CE1T1-PRI module in cisco 2821 router. In this module i want to terminate the PRI line, anyone can tel me it will support the SIP trunk protocol.Thanks,Karthik
Hello guys,I am having an issue whereby a cucm ver 8.5x sending the emergency calls to a H323 gateway always fails. The phone rings for about 4 or 5 rings then the call is dropped. I suspect the emergency services are expecting something that I am ...
i am trying to configuredqsic trunk between cme and panasonic pbx.but the controller is down.here is the show command.cme#show controllers e1E1 0/2/0 is down. Applique type is Channelized E1 - balanced Transmitter is sending remote alarm. Recei...
We want to connect our two cucm-clusters via cubes. I have tested SIP and H323. Both works fine. But we would like to have one feature: CALLBACK. Now i tried a intercluster-trunk using qsig, but this does not works with the cubes.CUCM-Version: 7.1.5C...
Hello Everyone,I have been behind the scenes and have reference many of topics and discussion in the support community. The time has come that I have some questions in regards of a migration from CUCM 7.1 to 8.X.The project is to migrate our current ...
Hello Friends,I have two questions:1) I´d like to know, how much 7914 module can i add at 7960 phone? 2) I connected one 7914 module at 7960 phone, but lamps 7914 module always is on red color and red lamps don´t off....What can i do with that? Hope ...
I'm facing the Issue, but slightly differ. while backing up my unity express information....Reports---> Backup History:HistoricalData: Failure Connection to backup server failed: ftp://X.X.X.X/mrv-unity:returnvalue:7Unable to connect to backup server...
