Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hi all,here is my issue ,i am using cisco 2851 ccme , i am having my boss extension and her PA extension , what are all the calls coming to boss it has to goto PA including the local extension call.then PA will transfer the call to my boss , i made e...
I'm attempting to us the IP SoftPhone on a Win7 x64 bit as a SIP phone not attached to a handset with it's own extension. The CME is version 8.1 hosted on a 2901 router. I have created the extension and profile for a SIP connection but the SoftPhon...
Hi everyone!I can't find any information about what cisco telephones are supporting h.323 protocol.There was a 7905G h.323 telephone, and now it is end of sales. Replacement is 6921 which is not supporting h323, or it is not written in the datasheet....
AllNeed some advice, I'm looking at an SRST site where PSTN callers are getting on hold tone and not the configured multicast MoH source. The only decernable difference between this site and all other sites is this uses BRI ports in trunk group. I ha...
Hi,I have some doubts regarding CME redundancy and i don't found answer reading the guides.1- Should i configure the second CME router (Backup) with SRST configuration (callmanager- fallback) or config like a CME (telephony-service)?2-Should Hardwa...
I have 2 questions regarding Music On Hold options for CME 9.01) Can you use unicast or is multicast the only option on CME 9.0?2) On a L3 3750 switch running IP BASE, is it possible to deliver MOH on the Voice VLAN (SVI) utilizing PIM STUB routing?H...
HiI have the following setup CUCM 6 -- > H323 GW ---- > SIP from same GW ---- > SIP providerWHen i dial a number across the SIP provider the number rings ,but as soon as i answer the call the call gets dropped ,but from the SIP debugs on the gateway ...
Hi, I would like to roll back to an older version of firmware - SCCP 9.2.1.0 (Active Load) to SCCP 9.0.2.0 (Inactive Load)We are using CUCM 7.3.1Tried to manually assign the Phone Load Name on the device to "SCCP69xx.9-0-2-0" [device][phone][ext][pho...
I have Cisco Unified Communication Manager Cluster( version: 8.6.2.2000-2).I will add a new subscriber to existing cluster. I have : a new 8.5. instaliation dvd , 8.6.2.2000-2 upgrade dvd.is it possible to add the new subscriber to cluster. or is it ...
Hello Folks,I am almost done with an Avaya S8400 and Cisco CallManager 5.1 integration using H.323 trunk. The only issue I have is the Caller ID & Name from Avaya to Cisco. The display shows "Unknown unmber". The Avaya users are able to see the Calle...
Hi, what are the requirements in order to purchase off of the VG224-MP part number? Also, is there a 4 port T1 card coming out? Thanks
voice translation-rule 1rule 1 /^9/ //voice translation-profile 1translate called 1
Hi guysI'm with a big problem in my customerThe customer associate users (from LDAP) in owner ID (field) in the phones devices.Well, sometimes (all weeks), employees are, how can I say, they take a "job-licensed" (sick, accident at work and another c...
Hello,Was anybody solved this problem?http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCto3125669XX phones have 10 min TFTP DL timeout. Upgrade fails over WAN. Symptom:69XX model phones (6921, 6941, 6...
Hello,I had our telco company install a single PRI last summer. The PRI feeds 5 locations, all of whom we disconnected their analog lines and they now ride on our PRI line at Location A. I needed to setup 911 so that when calls originate from any of ...
| User | Count |
|---|---|
| 8 | |
| 6 | |
| 5 | |
| 4 | |
| 4 |
.jpg "VIP Expert"){kind=icon}
