Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HiWe have a QSIG link between a 3845 and Avaya PBX. When we try calling across it (IP to Analog), the phone rings but there is no audio stream when going off hook.Any suggestions on what could cause this type of behaviour?Thanksconfigcontroller E1 0...
HI,Im trying to get the redirect called number working during SRST fallback.Our network setup:CUCM 7.1.5 and CUC 7.1.5 located at the HUB location, SPOKE site IP Phones regsiter to HUB CUCM/CUC via private network point to point. Both sites have voic...
My carrier claims that the Cisco 3845 voice gateway by sending a default prescendce level on the PRI trunks for MLPP is the reason I cannot place outbound calls on my new trunks. Can you even disable this setting? I don't have this problem on other i...
If the number of DSP resources required is as the followingDSP required for 5 Conference bridges = 5 and DSP required for 32 Transcoder sessions = 8 (each DSP can accommodate 4 transcoder sessions)How many DSPs required for ( maximum sessions hardwa...
Hi,we need to offer BE6K-UWL-100USR bundle to a customer, we did this using Cisco Commerce Workspace CCW, my question is: do i need to order the VMware Vsphere 5 VMW-VS5-ST-1A= qty 2 as the UCS comes with 2 processors or the VMware vsphere should be ...
HiIs cisco UC540 is supported by TAC ? Any TAC support available for UC540W-FXO-K9In TAC I can see UC520 but not sure TAC support UC540.Pls. clarify.RgdsRajesh
Hi SupportI have cisco 3845 with cme installed.using 3 ip phones, 2 7911 and 1 7940.the 3 ip phones are working fine, can call any ip phone from another.My issue is when phone start, i have some error message on the screen of 7960, file not found bef...
I am trying to create the prompt management on CUE..l I have the dial-peer setup. Callhandling is setup. User setup as administrator and still doesn't work. What am I missing?
Hello. I'm trying to a PRI while it is also registered to CUCM (long story as to the need for this). I assumed this would not be a problem, but I cannot get it to work, so can someone clarify? I can neither use csim start nor isdn test call effect...
Hi Guys,I'm going to upgrade a CUCMBE 6.1(2) to 8.6(2a). I have search on the upgrade guide but I couldn't find a detailed guide. Basically I'm going to upgrade using the same 7828H3 server. However I found that I require some USB External drives. Ca...
Hello..Please, If somebody can help me, I would be grateful..I need to block some inbound calls on CUCM..Is it possible to do this on CUCM 8.6??...How can I do that?...Thanks in advanced.Regards.
Hello ,Request for ANY white paper or previous experience to link the 2 system by SIP trunking ?will be a great help
I know that this may be heresy, but some customers seem to have bitten on the "free" Lync capabilities.Have a potential customer that has a bunch of Tandberg Edge95's and a MX6000 that they are using for H.323 video today. I am providing them quotes...
Hi,The phones do not load the new version of CUCMv8.5. to force the update I'm doing a manual reset them, using the sequence 123456789*0#. Then the phone updates the version of the firmware. In the CUCMv8 Administration, I perform a reset in the butt...
Dear NetPro,My customer has a lot of users come & go and they use 'Extension Mobility' for all of their users.My client is trying to investigate what extensions are vacant since users may have left. Does CUCM has any way of discovering what extensio...
