Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All,I just would like to have some expert opinion on the probability of using IVR through Unity Express and then calls should route to Call Manager.For example, If we have a Site with 2800/2900 ISR Router with Unity Express Module NME-CUE and Cisc...
Hi all,I am trying to upgrade the firmware on a 7945. I've done the steps like every other phone type I have, of copying all files to flash, tftp-server flashing them, going to telephony-service and "load 7945 SCCPxyz", but when I reset the phone, it...
In my lab setup have two seperate 1760 CME 4.1 routers serially WAN'd to a 2620XM router using RIP, that has the Unity Express NM-CUE 3.1.1 module in it. The 2620 is just doing the voicemail and routing between the two CME's, no ca...
Hi after upgrading the callmanager from 7.1 to 8.0.3 i found extension mobility not working. I was told i had been hit by bug CSCsy76489 by cisco tac. I cant find any information on this particular bug on the tool kit since its still internal. I wond...
HiI have spent 2 days behind this little issue and still cannot figure out the catch. I have CISCO3825 with IOS c3825-adventerprisek9-mz.151-4.M4.bin and cme-bacd-3.0.0.2. I just need AA and no need for hunt group. here is the config:dial-peer voice ...
Hi All,Is it possible to do fax over IP which topology below?Fax <<>> VG+transcoder <<<<<H323 G729>>>>>> 3rdParty PBX <<>> FaxBR WINAI
Hi,We are facing a problem in our production CUCM 6.After the power shutdown neither the Pub or Sub is doesn't work the Pub is asking for recovery disk "which is not available in our stock".And the Sub is running but I couldn't access the cm administ...
I have installed an AQM version 2.6 with CUCM 7 and UCCX 7.I have followed the instalation guide but I have some problems, I had some logs from Event viewer but I haven't found any information to fix them.Logs:RecordServer: The description for Event ...
Hi, i want to see whats the easiest solution to generate a call report from a cisco telephony. I was trying to generate it from the cli, but i just cant fin the way to do it.I will apreciate your answers.
Does anyone know how to find the manufacture date of a Cisco IP phone based on its MAC address of Serial number? Is it the same as with routers & switches?
Hi,I am facing issue with my cisco unity module (NME-CUE). My router (2911) rebooted accidently and it boot with the IOS 15.2. after that my voice mail system gone down. In 15.2 it is not taking command for integrated service engine. Now I have reloa...
Hello,From debug isdn q931 what means the following: Cause i = 0x80E46C - Invalid information element contents Call State i = 0x06When I call outside, the calling number is not transmitted.Thanks
Hi Everyone,I have Integration of CUCM8.5 with Microsoft Lync 2010 through sip trunk (CUCM_Lync). currently enterprise-voice-service-enabled-users in Lync Server are able to call / dial other lync clients and IP- Phone extensions simaltanously. CUCM ...
I have configured the CUBE->CUCM voice calls inbound and outbound.Has anyone been able to get Video Calling working over a SIP Trunk? I am using a 8945 as the video inpoint.Thanks,Edwin
I am upgrading from CUCM 6.1.5 in a VM Workstation Lab environment in anticipation of receiving my new hardware. I am trying to download 8.6(2)SU1 from Cisco and it says it should be 4.4gb but I only get 437mb at the completion of the download.. Is t...
