Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,One of my client have one MCS7816-H3 server with 2GB memory. Now they want to upgrade this server with 4GB memory. When I search in cisco I found that MEM-7816-H3-2GB= is the part number for the particular server. But this part is in EOS. Can any ...
Hi ,I am planning to upgrade the CUCM v8.5.1 to v8.6.2 . I was searching for the links to verify the hardware compatibility before doing an upgrade , but unable to find the same on cisco site. Can some one help me .Thanks,Siddharam
Hi,I have configured Cisco Unified CM rel. 7.1 and installed Cisco IP Communicator 8.6. Incoming calls work fine but I am having problems making outgoing calls. Would very much appreciate any advise. Thanks.Regards,Mohammed Noor
i want to conncet a cucm server to asterisk server.
Good Day,Dear Cisco support team,I have a setup where i have running cisco unified communication manager 8.5 , Publisher and subscriber.I have Mircrosoft Exchange UM 2007 for auto attendant and voicemail.I have created a sip trunk between Microsfot ...
I am having an issue with landing and inbound call through MGCP gateway to IP Phone that belongs to a partition 1ST-PT:PSTN->E1->2811->MGCP->CUCM 7.0.1->IP Phone1) As soon as I take out IP Phone from it's partition into <none>, inbound call lands jus...
UCCX redirect calls to extension, the reciever pickup the call and hears nothing - silence.He hangs up and get a second ring, he pickup the call and get connected.all the while the initiator hears ringback and obviously it takes unusually long time.T...
I need the link the updated firmware version for both phones
I recently bought 350 Cisco 7962s for UCM 7.X of those 350 about 100 of them I cannot access our corporate directory. I get an error saying to contact the administrator. I have tried to do the factory reset; there are no Config differences between th...
Hi all,I have a design problem replicating Ericsson MD110 ADN feature on Cisco CUCM 8.6.1, and any help / suggestion is appreciated !Customer is Power distribution company, and Dispatching center is the issue. There is one main dispatching center, an...
hi all,when i tried to install the 8.6.2 upgrade packet on my CUCM 7.1.5(the software license is demo), the message appears:Upgrades are prohibited during the grace periodand I look for the cisco.com then found something http://www.cisco.com/en/US/pr...
HiOne of our client has C2911 router with CME. The telephony ver is 8.8.We installed an ISM module in the router but the AA does not accept DTMF tones. I will appreciate your sugegstions to help me fix this problem.CME#sh verCisco IOS Software, C2900...
Any roadmap to have cucmbe3k in latinamerica ready to be offeredSent from Cisco Technical Support iPad App
hello everyonei use SIP 7942 connect to aspect core controller ,when i dial a keystoke i hear two DTMF tone but SIP 7940 is just one DTMF tone.here is the file form SCCP to SIP 7942 how can i resolve the problem
I am trying to connect my old Bogen V100 Amp with a Tel1s module in the back to my Cisco Voice gateway. I have wired it up and I tested the speakers are working. But when I call my overhead paging number I get nothingAny idea is the module Bogen T...
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
