IP Telephony and Phones

I MISTAKINGLY DID A FACTORY RESET OF MY CISCO CP-7945G IP PHONE ..ALL I SEE WHEN I START THE PHONE IS" UPGRADING" MESSAGE WITH SOMETHING LIKE THE PHONE MAC BELOW AND THE CISCO LOGO..HOW DO I CORRECT THIS PROBLEM

I MISTAKINGLY DID A FACTORY RESET OF MY CISCO CP-7945G IP PHONE ..ALL I SEE WHEN I START THE PHONE IS" UPGRADING" MESSAGE WITH SOMETHING LIKE THE PHONE MAC BELOW AND THE CISCO LOGO..HOW DO I CORRECT THIS PROBLEM

Calls to extention auto added to meet-me conference in progress

We have a little issue which I can't seem to put my finger on.When my boss initiates a conference call (meet-me) from her extention (7940 ip phone), incoming calls to her extention get added to the meet-me call. How can I prevent this.Call Manager 4...

Unity 7 - Menu Playback slow on one mailbox

Application: UnityVersion: 7.0Platform: Windows Server 2003Message Store: Exchange 2003CUCM: CUCM v8.6I have one user who has reported to me that when he is checking his voicemail, the menus play very slowly. Any clue where to start on this? I checke...

Device Association

Hi,I'm running CUCM 6.x cluster and getting organization's user info through AD. Need to associate 2500+ ip phones with the AD user accounts.Is there a method to do this using bulk administration tool?Thanks.

AD & CUCM

Hi Experts,t Our AD and CUCM directories are not synched. I tried to manualy force the synchronization by stopping and starting the Cisco DirSynch but no luck.Questions:- Is this the only way to manually synch the AD and CUCM?- When and how o...

Reset CAR Admin password

Customer is using Call manager 7.x and have lost CAR admin password.Now they can login with a user but cannot generate QoS Detail reports. To run those reports the user must have Admin privileges. Problem is that we cannot assign admin privileges unt...

Resolved! E1 or T1 between Two MGCP Gateways with a CUCM per gateway

Is it possible to configure E1 or T1 between 2 MGCP Gateways?I have a Cisco CUCM 7.1 and a CUCM 8.0.3. both had their own MGCP Gateway. is it possible to connect both of these together by E1 or T1?I have the inter-cluster link already in place and it...

MGCP and Gatekeeper

I cannot have the CUCMs register with a gatekeeper since there are already Inter-Cluster Trunks (non gatekeeper controlled) configured. Gatekeeper will be used just for TEHO. Since you can configure H323 and MGCP on a gateway can I configure gatekeep...

[RTMT-ALERT-StandAloneCluster] LowAvailableVirtualMemory

Available virtual memory below 30 Percent.tomcat (925 MB) uses most of the memory.The alert is generated on Wed Jan 26 16:11:35 GMT 2011 on node X.X.X.X.We are getting the above mentioned alert quite often.I have been restarting the TomCat service to...

cisco unity connection -- invalid selection

Hi, We have two users where when they try to login into the voice mail, they get this, invalid selection message, tried changing the password several times over , but its of no help. the extension and all other stuff is fine. Cisco unity connection ...

Resolved! Extension Mobility (7960 type) fully compatible with 7962 hardware?

Hi all,We have lots of 7960 phones deployed which all work really well. We have Ext Mobility overlaid on these, and staff can happily logout and login where they like with no issues.We rolled some colour 7970 phones out a few years ago and found that...

Gatekeeper Trunks

What are the ramifications of having a gatekeeper controlled trunk and a non gatekeeper controlled trunk off the same cluster? Thanks

Trouble calling from CUPC 8.5 to Cisco Video IP Phone E20

Hello All,We are trying to make a video call from CUPC version 8.5 to Tandberg E20 and the video call is not possible, we only have an audio call without video. ¿Can you tell us if the problem is probably compatibility? ¿Someone did before this test?...

Resolved! Identifying Q931 debug data for one user on a 30 channel E1

I have an PSTN E1 circuit into a 2901 voice gateway. I have one user on a specific internal extension who is convinced they are having calls dropped.When all 30 channels are busy it's near impossible to trace a call through the debug output.Is there...

CUCM/SRST - Phones failover to SRST but don't failback

I have an issue where a remote office that registers with a CUCM over an MPLS link - the MPLS failed and the phones successfully failed over to their local SRST router. The MPLS was down for a period of time, so the site was reconfigured with a L2L ...

IP Telephony and Phones

Forum Posts

I MISTAKINGLY DID A FACTORY RESET OF MY CISCO CP-7945G IP PHONE ..ALL I SEE WHEN I START THE PHONE IS" UPGRADING" MESSAGE WITH SOMETHING LIKE THE PHONE MAC BELOW AND THE CISCO LOGO..HOW DO I CORRECT THIS PROBLEM

Calls to extention auto added to meet-me conference in progress

Unity 7 - Menu Playback slow on one mailbox

Device Association

AD & CUCM

Reset CAR Admin password

Resolved! E1 or T1 between Two MGCP Gateways with a CUCM per gateway

MGCP and Gatekeeper

[RTMT-ALERT-StandAloneCluster] LowAvailableVirtualMemory

cisco unity connection -- invalid selection

Resolved! Extension Mobility (7960 type) fully compatible with 7962 hardware?

Gatekeeper Trunks

Trouble calling from CUPC 8.5 to Cisco Video IP Phone E20

Resolved! Identifying Q931 debug data for one user on a 30 channel E1

CUCM/SRST - Phones failover to SRST but don't failback

Hearty congratulations to the December Spotlight Award winners!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

CUCM 14 LDAPS certicate issue

CUCM sends wrong device ID to Recording System

CDR reports: Request for activity on multiple lines

I get dozens of these alarms on WU, but no errros on controller

Transfer Caller ID and 8800 Line Buttons CME

4331-Vk/9 router replacement can it be C8200L-1N-4T

CUCM 14 "Operation Completes by" Problem with 2023

Call forwarding not working ( Vodafone Germany)

7861 BLF Phone not showing green idle status.

Voice call flow working just one direction in VOIP CUCM to POTS CME