Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello Dear,I need to help the configuration.I have configure PSTN pots configuration.Incoming call is not coming. Also cant configure outgoing dial peer.Below as my configuration .Note: I am new in this filed. Please help the the configuration. voice...
Hollow community. My users which are to be installed on cucm have firstName, lastName and staffNumber. I'm looking for a way to anonymised the userId. can anyone share any strategies that they've used please? The purpose is to limit the storage of ...
Greetings everyone.I can not find a solution for this case, after replace the motherboard, put more ram, change IOS Version, re config everything, and stills the CME on the C3845 getting hung in a perior of time from 10 to 15 days and ephones disconn...
Hello All Experts, I have been trying to figure this out but not sure how to? If I want to trace calls INBOUND, OUTBOUND, SIP, Fax calls etc. so I can figure out the PATH and gateways/trunk involve in a call from a site to PSTN and PSTN to site. Wh...
Hello I'm deploying a CUBE to connect a SIP TRUNK to ITSP and I'm wondering if its recommending to put a CUBE in the LAN or It's best to put it in DMZ? If I put it in LAN or DMZ which IP should I give it to my ITSP to build the SIP TRUNK?
Hello everyone,I have some Cisco 7841 phones which cannot register.In CUCM the load information is sip78xx.11-5-1-18 but the 7841 software version shows sip78xx.11-1-1MSR2-1.loads.I tried a firmware upgrade to sip78xx.11-5-1-18 but it did not work. A...
Hello, I have to update more than 1000 phones, specifically a single speed-dial button items. I know i have to use bulk administration for this, how can i go about doing that? Thank you in advance!
Hi all,Trying to install phone firmware version 14.0, released last week. Release notes say it can be used on CUCM 10.5 or higher. We're running 12.0.1.The new firmware has a new file extension of "cop.sha512" instead of "cop.sgn", and when I try to ...
Someone (prior to me taking over) removed both the Corporate Directory and Personal directory options from all phones. When you currently press the Directories button on the phone the only options you see are Missed Calls, Received Calls, and Placed...
Good Morning ColleaguesI hope you are doing good . I have CISCO 2801 router that is configured successfully as follow: Connect to 3CX IP PBX successfully.2 CISCO softphone (CISCO IP Communicator) has been registered successfully to CISCO 2801.CISCO I...
Our company just learned about the new Kari's Law and Ray Baum's Act being implemented by February 16, 2020.For obviously reasons we are behind the eight ball and need to learn whether there are any quick and easy ways to get this implemented? We are...
Hi, all good day; I have a network with 4 VLANsVlan10 for DATAVlan11 isolate with ACL for small groupVlan12 Voice VlanVlan13 Wireless Vlanall the telephone office connect to CUCM 192.168.12.14 and 192.168.12.15 (secondary)vlan11 has an access-li...
Good Afternoon ColleaguesI hope you are doing good and safe .I am trying connect CISCO 2801 as VOIP gateway with IP PBX 3CX. The SIP trunk is up between them but a piece of configuration still missing. The dial peer between CISCO & 3CX is 20000 . I n...
Hi everyone , hope you doing great , i have to change all Employees phones ,all info will not be change only device type , so is bulk admin is best solution ? thanks in advance .
Hello, I want to play an message before calls to cisco ip phone and to learn how to do this? For example; Calls come to CUCM ext: 4040 Aim is play an message to caller before 4040 ring.
