Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Evening All,I am applying for a position for a Cisco Voice engineer - I have just recently passed my CCNA voice exam.Basically, the post was asking for a ccnp voice engineer - but the salary was below what I expected for that qualification anyway; so...
We received some Cisco CP-7945G phones from our head office to replace the CP-7940G's we had in place. I'm having an issue with these phones, when powered on and plugged into the network, they are stuck on initializing for a few minutes, then they t...
Looking for pro's and con's of upgrading CUCM 7.1(5) to eith 8.5(x) or 8.6(x) in a few weeks -- we have concerns about going to a new version that is a "dot-1" release, or without SR's. Do you have any thoughts on the subject?
Hello,I'm configuring SIP 9951 phone on CME 8.6 but cant call to CUCM , at the same time with SCCP 6941 calls to CUCM there is no problem. Calls to SCCP phones on the same CME is working well too.But when i call to CUCM from 9951 i hear in about 5 se...
Dear allcan i get help how to configure Cisco Mobile 8.0 in Cisco Unified Communications Manager Express Ver 7.1thanks
Hello Everybody,It been 3 days , i´m working for this subject "how to change the background of my ip phone in my cucm cluster ".I have read, and try a couple of tutorial, but it still not workhere is the details :Cucm 7.1Model phone 7962size image lo...
we have a new SIP line from PSTN of bandwidth 16mb(not sure about the bandwidth)the ISP given one access netwotk 124 modem, i need to terminate that line to our H.323 voice gateway ,can anyone please tell me about what configuration i need to do i...
We are running CUCm 8.0 now and in about 3-4 weeks we are going to upgrade to 8.6. We currently have customers call in and press one on their phones to go to the Customer Service department. I would like to have them be able to have the choice of pre...
Hi,I'm frequently getting 503 and 500 errors on CUBE. If I call from a phone not on CM/CUBE, I can reach the destination number. It is an intermittent problem. Please see the below:*Apr 2 15:01:18.907: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:Receiv...
Is it possible to turn on/off the auto attendant from the phone. Currently the auto attendant is setup on time based schedule. Thanks in advance.
Hi,I have CME 8.6 & CUE 8.6....Reception phones are in a hunt 555 & actual phone DN is 500 & 600....I have forwarded all calls towards CUE with the below dial-peer:======================================================dial-peer voice 1 voip descripti...
I am tying to setup voice gateway to fall back to voice mail when in SRST mode. I would like to know is this right configuration and do I need to use the Transfer-pattern .T to transfer the 10 digit number.Thanks,Configure Tcall-manager-fallbacktrans...
Hi there,Is it possible to set up an ephone-dn shared line between ASA-187 (SIP) and a SCCP phone?Thank you.Regards, Norbert
I am trying to figure out how to get caller ID displayed as follows:If a user configured for mobile connect is sitting at their desk and dialing to external users their CID should show up as the main number and not their DID. I have their line confi...
HelloI'm looking for some advice and information. We are getting notification from RTMT that some certificates are about to expire on our publisher server. These are tomcat_cert (own), ipsec_cert (own), CalManagerUnit (own), CAPF (own), and CAPF-XX...
