Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
IS it possible to make it happen that one extension registered on cucm will use one designated analogue number connected on voice gateway?
I have 2901 router with ISM-SRE-300-K9 module for CUE.I am trying to install cue 8.6 on this module as the cue boots in bootloader I am following the procedure as listed in http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel8_6/install/boothe...
Hi everyone,first time poster on here. i'm looking for some input on an issue i've been trying to resolve. We upgraded our phone system for an old legacy system back in November. We were using 12 analog lines to handle our calls and we are now usi...
Hi All,Current status : We have CUCM 7.1.3b in place on MCS 7816Requirement : CP-3905 phones required to by and use with CUCM CP-3905 works from 7.1.5 version and later versions and it requires UCL license to be opted no option ...
Were starting to upgrade our 7940 SCCP phones to the newer 8961 & 9951. On the newer phones I noticed that the handset mic and earphone work a little different now. The local mic input(my voice) no longer plays in the earphone when I speak. I'm sure ...
We get "recovery on timer expiry" from Cisco IOS debug isdn q931.We have amended the T310 timer according to document 18659 (Call Failure to Long Distance/Mobile Destination).However "recovery on timer expiry" problem persists. We cannot see any diff...
I have a CME will likely be a 8.6 or 8.8 Does anyone have a clean way to stop extension "a" from calling extension "b" It is really two seperate companies on the same CME so they dont want company "a" from calling company "b" basically a multi ...
Hey guys,So, I don't think this can be done, but it was given to me to find out so here goes.Three sites, let's call them as follows"Site A" DID range is "1112223333-4000""Site B" DID range is "4445556666-5000""Site C" DID range is "7778889999-6000" ...
Hi guys,I am trying to configure an E1 PRI in Nairobi. TelKom Kenya has proved that the cable and Exchange is good by having an IP Pbx onsite. I am on a CM 7.1(5b)su4. The remote site is on a 3845 GW. The E1 PRI card is VWIC2-2MFT-T1/E1 - 2-Port RJ-4...
Hi all,Can anyone point me in the right direction regarding the following issue.We have a Inbound number mapped to a Transform pattern that forwards to a CTI (virtual DN). This in-turn connects to CCX and runs a basic script. The script asks the call...
Were starting to upgrade our 7940 SCCP phones to the newer 8961 & 9951. On the newer phones I noticed that the handset mic and earphone work a little different now. The local mic input(my voice) no longer plays in the earphone when I speak. I'm su...
Hello Folks,Has anyone used a FXS/DID to teminate an analog phone line from the telco?I am trying to terminate 8 Analog lines on a CUCME 8.5, the line will be be associated to two different BTNs, which are configured as huntgroups on the telco side t...
Hi there,I know that CUCM, Unity-Connection and Presence are only supported with the version 8.x &+But,Lets say, I have my production that run on MCS server at 7.1.3 and I want to do re-install on a UCS Server.I would like to install 7.1.3 on the UC...
We are facing an issue with accessing our voice mail externally : To access the Voicemail system, from outside the office: Dial – 123-456-7890. ID: last 4 digit of your phone number. Password: your voice mai...
Hey everyone..Looking for a way to setup the ability to call forward all from Line A to Line B, and allow Line A's Voicemail to pop if nobody answers line B after lets say 4 rings. The catch is.. Line B is a lobby/shared space phone without voicemai...
