Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Any body can help what is wrong with this config. and how I can get auto load from CUCM, I am unable to get phone loaded, please see attached phone regesteration log.telephony-servicesrst mode auto-provision allsrst ephone template 5srst ephone descr...
I configured a Unity Express 7.4 at AIM-CUE module at 2821 CIsco Gateway. I connect it to Cisco Callmanager 8.5 succesfully, imported teh users, created mailboxes, Pilots, Ports and so on.The users can call there voice mailboxes and create greetings,...
Hello everybody !!!I have been facing a call transfer delay at the follow situation.My scenario are 1 Cisco 3845 CME with 4 E1 links conecting with PSTN and 2 PRI ISDN links connected with Panasonic PBX KX-TDE600.There are an ICD group at Panasonic P...
Hi,We are planning for IP Telephony solution. We need at least 64 Simultaneous calls in system. Call manager ca support up to 1000 users. We are option for Cisco Business Edition 6000 series. SO, How many Concurrent/Simultaneous Voice calls can ha...
Hello ProsI have a setup where 3 CME(1861)s which by customer requirement need to send all calls to the PSTN through the Headquarters (With another CME running on a 2911). I am using SIP. And all seems to work fine.However, failover is needed through...
Hi,We are planinng to upgrade cucm 4.0 (having three cluster) to 8.0. We have query regarding dlu, can we use same dlu with 8.0 or we need to purchase new dlu.Please suggest me if any document is there on the same.Regards,Dinesh Joshi
Whether phone number digits can be seperated with spaces or - or some such to break them up for easy to view. I believe its not, but still looking if can be customized in any ways.If you receive call and caller id normally displayed as 5551211234 wh...
Dear friends.. i know this topic has been discussed loads of time and if i try on google i can get hundreds of huge books on this topic .. but if someone can guide me in short how can i setup this .. what all things i need... sorry ... i know thi is ...
Hi I am using Cisco 2811 router to converge 2 RTP streams of different codes. I have scenario as below:SIP PBX-------g729------>CISCO2811-------g711------>CUBEI am using the universal transcoder, it does kick-in but no rtp gets established. Could som...
Hi all.One of my client has problem with call disconnection.When my client try to end outbound call, call connection is not disconnected.My client calls to my cell phone(or my office phone)and my client ends call.But in my cell phone, call is not END...
Hi ,We have CUCM 7.1.5 . E1 PRI integrated through MGCP. When we call from the mobile phone to DID numbers call disconnected with following Cause codes.0x80BF Service / Option not available. This is happened for some users only . For rest of the use...
Hi,We have enough resources ont he CISCO2811 router for transcoding. We have resources available to handle 30 calls but it does not take more then 16 calls. The issue of not taking more then 16 calls is now a challenge. Here is the output of the ' sh...
Hi All,Just wondering if anyone has successfully made calls from an EX90 via the PSTN when registered to CM8.6? Video calls over the WAN to other EX90's work perfect.I've made sure the correct CSS is configured but still not able to make calls.The de...
hi thereI need help with undertanding DSP and its usage....i have tried few docmentations but still not clear when comes to troubleshooting/Design perpective..is there any documetation that some can share that has very clear instructions...CheersMany...
Is it possible to have the CUCME system monitor the FXO port for a stutter tone dial tone? My telco changes the dial tone when they have a voice message waiting. Since my phones are IP based I hear the CUCME dial tone rather than the PSTN dial tone. ...
