Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
So I got a Cisco 7821 3PCC phone from someone on eBay who resells them after getting them from other places. The phone is in great shape. However, I can't even web into it but I can ping it on my home subnet. Furthermore, I am unable to reset it to f...
Hello - I'm working with CUCM 10.5.2. We have 1 publisher and 7 subscribers in our cluster. Recently, one of the subscribers in the cluster is not allowing Extension Mobility logins for newer users. When I look at the publisher, the user looks fin...
Can a cisco 3640 with and FXS card or a VG204 be configured to connect to a VOIP servicein the same way as with an SPA112 ?
i have cucm 12.5 and 2921 h323 voice gateway , if i set on a phone a forward to pstn number and i call from a pstn number i get"all circuits are busy" but when i call from an inside extension and get forwarded to a pstn number it works fine . i have ...
Hi everyone and thanks in advance. I have a site that has 4 POTS lines, but at that location there are two separate houses that share the lines for inbound/incoming calls. am trying to separate the lines for the houses that way 2x lines for House A a...
Now I want to modify the unanswered ringing time from outside to inside extension. The gateway is ISR4331, h323 voice gateway. Service aa is enabled on the gateway.Now the ringing time when no one answers is 1 minute. I want to know where I can modif...
Hi, As I said, smaller part of CUCM cluster is down (2 of 5 servers), and MRA is working significantly slower and more inconsistent. Symptoms: -users, when try to login, get the message that the network is down, after they try couple more times they ...
I have an MGCP Gateway configured with the following translations that should only kick in with Fallback/STST.They are as follows!voice translation-rule 1rule 1 /^.*\(....$\)/ /\1/!voice translation-rule 2rule 1 /^.*$/ /90\0/!!voice translation-profi...
Hi Folks, CUCM V12.5, Expressway V12.7. Jabber for windows and Android (haven't tested IPhone). Everything works fine BUT when dialling out to the PSTN, the jabber user hears two ringtones. All is OK when not traversing the expressways.Any ideas folk...
Hello everyone: I´m trying to understand the console log of the phone CP-7841.Does anyone have a manual or a guide to help me?Thank you very much.
I'm setting up a pair of CUBE's in HA connecting to the SP with a VIP on the outside. I can make outbound calls, but when trying inbound the call fails: The initial invite from the carrier sends min-se of 300.CUBE responds with 422 Session Timer too...
Hello, We do a search in call manager within the route plan report, however the view file it shows all of call manager phones and partition not the search criteria I got from the route plan report. We have cucm 12.5. Why isnt view file not reflecti...
Hello everyone:We have a small call center with two phones (model Cisco CP-7841)That model have an option to call forwarding to the other phone in the same network if the volume is decreased by the operator to the minimum level. The call is not answe...
Hello,I configured recording with BIB function on my phone.It is a third-party recording server and a recording method by application.The result of analyzing the received voice packets to the recording server.A voice RTP packet arrives on the recordi...
Question I'm trying to test srst on an a replacement isdn 28XX with 4321.I put a acl on access switch to deny access to cucm and the phones. the phones go in to "service interupted" but no SRST service,However when i run #show ccm-manager it says t...
