Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi there!I need to develop a TCL Script to block selective incoming collect calls, ie, only some extensions would accept such calls.In Brazil, Collect Calls are identified with a specific subscriber category (II-8) in E1 R2 line.I need to create a sc...
Bonjour,J'ai des 7911 neuf, à la mise sous tension, ces téléphones reste une bonne vingtaine de minutes pour se mettre en marche.cela en utilisant l'alimentation POE.Avec une alimentation classique, je n'ai aucun resultat.Cette situation est-elle nor...
All, Could someone help me understand the advantangens the use of ISDN signaling instead of R2D?My environment has CallManager and Unity Connection.Thanks, Luciane de Medeiros
I have been going thru a lot of configuration in my lab at home. So far I can't find a reason why I need to use or when should I use a software MTP. I basically use a transcoders to do just about everything, but I know that i am missing something a...
Hi Everyone, I have a quick question; I have an FXO card at a remote site. The phone line plugged in to it is the main line for that site. We want to forward all those calls to our call center (CCX) but when I put the cti route point dn for the call ...
Hi there - I had a few users who started to get the 14 day notice that their VM pw was going to expire. I did a bulk edit and set everyone's pw to never expire, but they are still getting the pending expiration notice. Thoughts?
Unity 7.0 ES20, I need to install a 2nd language. Assuming the licensing is in place, what is the process? The language is Mexico - Spanish, if that matters.Thanks
hii,when I register a new 7945G ip phone on a existing setup (CUCM 7.1).it shows a line text label is highlighted which is not look good to see.and when I reset my phone it looks proper.Kindly provide the remedy for this issue.thanksRegards,Ramgopal...
Dear AllWe have integrated CUCM with LDAP succesfully My question is if we can integrade CUCM with secure LDAP ?Pls adviceregards
Hi All,The customer is using 187 ATA for the faxes and they are abkle to send faxes but are not able to recieve, could this be a telco issue or should i be looking closer to home?ThanksNathan
How many FXS ports are supported on a single EVM-HD-8FXS/DID? I've been getting mixed responses on this...from a documentation issue to a technical difficency in the EM3. And no, a VG224 will not suffice.The only documented method (see link below) fo...
my customer have a 3745 router,there is PBX+E1+R3745 in their Lan. customer want to upgrade 3745 to 3845.but there has a problem when i upgrade to 3845 ,the VOICE lost packet . the voice is ok when i try to "no ip tcp header-compression iphc-format"...
Hi,I do have a PRI line in HO with 200 number space. I have 2 branch offices conencted via MPLS with HO, without PRI line. I would like to allocate 1st 100 DID number to HO & rest 100 number in branch offices from the same DID range. Is this possible...
Hi,I am migrating CME 4.1 (2811 ISR) to CME 8.6 (2901 ISR G2). In CME 4.1 firmware load for 7941 is 7.0.3 and in CME 8.6 firmware load for 7941 is 9.1.1SR1. Looking at the CME 8.6 supported firmware document "When upgrading phone load version, first ...
HI All,I would like to thank everybody in advance for the help i may recieve.Im looking to implement a SRST solution with a sip backup. I have found guides to configure SRST for local/internal calls but i havent found anything that can help me from a...
