Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi, Just configured Unity Connection Visual Voicemail, and I confirmed each test step. Phone doesn't get Voicemail and Visual Voicemail options. It do just call the hunt pilot for Voicemail, always! I did all that I could. Only Voicemail, Only Visual...
Hi all,I have a customer with a requirement for Beep Tones for any phones that are recorded. I am not sure if it is mandantory law in Australia to enable such beep tones in the lines that are recorded. While there is such a Recording Tone option on t...
Hi,When I was going through Cisco Voice GWs and GKs book, I have read through the following.When CAMA trunks configured with reversal of TIP and RIGN wiring connections to the PSTN, the voice call will go through but it will get disconnected after 15...
HiWe have VG224 on production.Since it was not responding, we restarted VG224. After restart,We are getting "Original NVCONFIG doesn't have correct MAGIC number" error while bootup.We did power restart few times. Also, we have reloaded this device us...
can anybody suggest me what are the settings related to incoming calls on gateway and cucm earliest response highly appreciatedand i would like to know whether the DIDs might be the problem
Hi anybody,we are going to buy IBM servers 7825 I 4 V03 and we want to have a remote option. We tried two different RSA adapters with no success. After installing the adapter the server stops during system check (BIOS). May be this is related to the ...
Can someone help me to synchronise 02 Microsoft Active Directory Forests with a cluster of CCM 8.5 (01 PUB and 02 SUB)?
Hi,I'm troubleshooting a conference/Hold and transfer inside a SIP Trunk.The behaviors are the same : OnHold : When caller is set on hold, then it is dropped automatically after 5 seconds.Transfer : The caller A is set on hold, and compose the second...
HiCUCM 7.1(5) with only one server, MRG, MRGL, Device Pools and Regions correctly configured. No MoH is heard (like muted) when a phone is put on hold. This happens with internal as well as external calls.No multicast MoH is configured, no strange th...
HiI am getting a 10 digit DID from my provider and i am trying it to map to an extension. I am configuring CUBE 3825 router.num-exp 7065432223(DID) 34555 (user's extension)But it's not working. I am doing something wrong here.I do have incoming dial...
Hi All, As per title u might thinking i need to restart the Tomcat service, yes i did but still all to no avail.i get this error from console :%CCM_TOMCAT_APPS-JAVAAPPLICATIONS-0-IPMANotStarted: IPMA Application not started Servlet Name: Cisco IP Man...
I just got the ATA187 and have them working. I need to know if there is a way to change settings via a web page? Can't find anything in the online manuals. The part I need to change is turning off the second port. A lot of times we put them next to a...
I have CUCM 7.1.5 and i have an adtran 850. i have connected the 850 via T1 CAS connection to a 2811 running mgcp.I get calls inbound and out just fine. The only problem i have is that the calls show a call ID of unknown.Is there a way to add an exte...
Hi all,Does anybody can help me to set the correct time in a CUE ? Users get into their VoiceMail and the hour shown is different from the current time. I haveno seen any CLI command to set the correct time inside CLOCK command, neither of CUE's WEB ...
Can you enable/disable mobility directly from an IP Phone such as a 7970?
