Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi there, On a cisco 2821 router running IOS 15.1(4)M im trying to successfully configure 2 aa & acd scripts.First service/script ( set as the default app-b-acd-aa service ) for my main number, which accepts the call and then callers get 8 op...
I have a few things I need some help with. We currently have a business line set up that rings to 5 or so extensions. It has its own voicemail set up. There are some things I would like to change with this hunt group/line- I would like to be able to ...
Hi,Just wondering if anyone has experience the follwoing.For some reason when i enter the follwoing commands they don't show in my config. I don't get an error message when i enter them and i can also enter different types which are visible when i do...
Implenting a cucm7.1.5 solution with Cisco unified enterprise attendant console 8.5, during business hours if reception is logging out then calls are not going any where , it still rings on with calling disaly shows the CTI gateway number, i have con...
Hello,I have the following situation. I have my IP phone and my cell-phone combined as single number reach (mobile connnect). Lets say :A-calling party numberB-IP phone numberC-Cell Phone number"A" calls me to "B". CCM makes an outbound call to provi...
Hi alli wish know how to migrate data from Cluster UC CCM 7.0.2 to the new HW cluster with 8.0 . does DMA ?thanks a lot.
We are trying to create a trunk between two call managers one version 8.0 and the other 6.0.We have Voice working one way but the other way seems to be problamaitc. How would i go about troubleshooting this ?
Hi, I need to configure cisco 2801 router as an SS7 gateway from the PSTN side and a SIP dial peer from the VoIP side. The router include a E1 interface, Is this configuration is possible? is there a documents shows such configuration?With best rega...
Hi,we are running about 1000 VG2XX via MGCP connected to CUCM 7.1.5Since we already monitor CMR records for our phones we have enabled "mgcp voice-quality-stats all" on some gateways.Via "debug mgcp pakets" I can see the Gateway is sending these stat...
Is the ata 188 compatible with callmanager 7.1.3. I do not see it in the drop down menu. i have installed the latest dev pak. do i need to reboot callmanager after installing to see new devices. I didn't think i had to...Thank Youdan
I want to config the Max calls of SIP phone on CME.I know ,for SCCP ,it is "max-calls-per-button" but for SIP, what is the command ?
Hi, we have a 2921 with an ISDN 30 from O2.The Gateway is configured as H323 and if i do an sh ISDN STATUS i see Layer 1 is Active and Layer 2 is MULTIPLE_FRAME_ESTABLISHED.With a DEB ISDN Q931 i dont see anything if do a Call from Outside to the Gat...
Hello,My config :ISR2811------(sip)--------NAT1-------(sip)--------NAT2-------(sip)--------SIP ProviderISR2811 : voice gateway, one network interface with private ip address 1.1.1.1NAT1 : third-party equipment with sip inspection. Two network interfa...
Hello everyone,I have configured a CUCM to connect to other three CUCMs (they are our business partners) using ICTs so we can communicate without the need to go to the PSTN.Everything works perfect but I'm running out of ideas about an issue we're ha...
Hi, I have a requirement here, customer wants to get the some kind of warning or notification after putting a call on hold over 1 min. Could you share with me if I can do this on CUCM and how to do that?CUCM 7 + Unity 4.2Thanks. Leo
