Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
When I access Service Activation Control Center Feature Services Control Center Network Services under Cisco Unified Serviceability I get an error “Connection to the Server cannot be established(Unknown Error)†when I select to access the service...
i have a 2800 cisco router with five lines of ip telephonyi need to transmit two lines to other siteplease note that : the two sites are connected by fiber optic and a switch (DELL) will receive these two lineswhat can i do ?please help
Hi, I just purchased an off-lease 7960 IP Phone and I'm having difficulty setting up the phone on my home network.The IP address, the Subnet, the Gateway are all verified and the device shows up on the server, but I don't know where to go from here.T...
I have a phone with extension 140. It is able to call my phone (we'll call it 555-555-1234). However, if it is set to call forward to 555-555-1234 and the CFWD ALL and I dial extension 140, I hear dead air for about 8-10 seconds, then a busy signal...
Normally for outbound calling the dial-peer is chosen based on destination pattern. I wondered if it was possible to have the dial peer chosen based in part on thecalling extension. The situation is this:A friend has a UC540 and for voice calls he ...
Hi There !I have a Hunt Pilot configured (1000) with 4 extension (1001, 1002, 1003, 1004) - BroadcastIf the 1001 extension pick up the call, 1002, 1003, 1004 extension shows a "missed call" information... but it was answered by 1001...What can I do ...
CUCM System version: 8.0.3.20000-2LDAP Sync with MS AD 2003 for Users.One OU has an & character in the name, wondering if that is causing problems because after the initial synchronization we are not recieving updates. In addition, when you select t...
Dear all, Recently my customer is using cisco cme 7.1 and they want to have the new FAC features. I know that in order to use FAC in CME, we must upgrade our IOS from 15.0 to 15.1(3)T. After the upgrade, I found that my phones cannot register to the ...
CUCM System version: 7.1.3.10000-11SIP Trunk to 3845 w/ 12.4(24)T3I need a solution for a SIP outbound callforwarding issue. We recently changed from traditional PRI to Verizon provided SIP. Verizon requires the outbound digits be 10 and a SIP number...
Hi Guys,We are implementing the Unity and is search the following problem: DTMF work only if there is transconding in the call (using G.711 or G729). To internal calls the DTFM work without transcoding, but, the when receiving the external call, does...
Dear AllI have CUCM 8.0.3.21900-8. MOH internally plays fine.But if the call is coming from PSTN or the call going to PSTN then the MOH not workYou dont hear a beep or something.But a dead air occurPls helpRegards
I'm having issues with my backups on UCCX 7.0 they stopped working they're not backing up? Where do I look to see what are the issues causing these backups from not working?Regards,Robert
Hi all,I'm on a project where there is need on voip communication between one office and a few workers.The main target is that the office people can communicate with the workers and in the other way BUT the workers cannot communicate with other worke...
I currently have Unity ver 5 in production environment and am migrating gradually to connection ver 8,5, I have the 2 connection servers built and licensed on VMware ready to go.Can anyone see an issue with adding the connection servers to callmanage...
Hi Guys,I am try to configure the Extension Mobility and after to do the logon the Directory Number doesn´t appear in the line. The Extension Mobility is working, but, in the Route Plan Report I don´t too to see the MAC ADDRESS. I Reviewed the config...
