IP Telephony and Phones

H.323 CALLING PARTY NAME

I have an installation with CUCM8.0. We have established a connection with a MD110 system through a H.323 gateway and a Q.SIG link. I want to know is there is any way to see the Calling Party Number in PBX Phones. In traces, I can see the name in the...

LOOKING FOR ANYBODY WITH SIP KNOWLEDGE - EASY QUESTION

I'm attaching a trace of a call from Phone A (5428, in my CUCM - 10.250.208.40) to Phone B (7321, in a PBX system - 10.229.128.54). Both systems are connected with a SIP trunk.I need to know if 10.229.128.54 is answering something or if simply there...

2921 CME Upgrade

Quick question; I think am missing something, even after reading tons of docs: I have a new ISR 2921 that came with IOS 15.0, and CME 7.1. I want to upgrade to CME 8.1; Do I just upgrade the IOS to 15.1.3? The CME admin guides says the following (b...

Intermittent reset of VoIP phones connected to Cisco 3750 switch stack

We have 5 x Cisco 3750 (WS-C3750V2-24PS) switches running 12.2(50)SE1 stacked in a LAN in a new office.A Mitel phone system is being implemented by a 3rd party on this LAN. There is an intermittent problem where some of the phones will reset themse...

CALL WAITING "BIP" VOLUME

Is there any way to low the sound of the waiting call tone? (the "bipbip" that sounds in the remote phone when you put his call on hold). In an installation that we are doing sounds very loud.Thank you very much.

Resolved! Incoming calls over PRI hitting Cisco 2650 gateway, but not Mitel PBX

Trying to have phone calls come in over a PRI, hit a Cisco2650XM gateway, then be sent to a Mitel Call Control server.PSTN----->PRI---->2650XM----->MITEL------>PhonesWhen I dial a DID on the PRI, I see it hitting the router:---snip----Dec 1 18:22:47...

Implementing Teho and AAR

Hello Guys, I have a question.I am implementing a large voice network in several locations.The customer wants Teho for normal long distance calls (we have a centralized ccm 7.1(3) cluster)I have created some route patterns like .88001 for a location ...

Resolved! Searching ip phone network

Is there any scan program for searching all the ip phones and reporting MAC, IPs from Cisco?

Resolved! URL

Can someone tell me or send me a link showing what the phone service URL's are for speed dials and fast dials?Thanks

CUE 8.0.2 VM Port Upgrade

Hi All - Thanks for the help...I purchased NME-CUE module for CME router and it came with 8 VM ports - I didnt' think that would be enough ports as there are about 150 phones registered to CUCME....so I purchased (4) SCUE-LIC-PORT-2= licenses with th...

SRST - Broadcast hunt group- is it possible?

Hi all,I am looking to see how to configure a broadcast huntgroup in SRST mode.I did some searching and what i find is, SRST cannot do a broadcast huntgroup but those posts were from 3-4 years ago.is that still the case? if not, how would i go about...

"dial-peer hunt" in CME SRST mode

Hi All,I saw the CME guide says we must configure "dial-peer hunt" command to make hunt group work during SRST fallback mode. Does this mean this command depress the hunt group during the normal operation and activate the hunt group during SRST. In t...

Feature and design question for CME and CUE.

I have recently installed and now using a CME and CUE system. I have a few question about some requested features the users are interested in.First a few technical issues. I have a 32 channel DSP, my telephone provider gives me access to a ISDN 30 (3...

Resolved! CUCM 4.3 --> 7 Upgrade Utility / DMA for Parallel upgrade

Hi All,Would like to to confirm for a parallel CallManager 4.3 -->7.1.3 upgrade that there is no requirement in running the Cisco Upgrade Utility on the legacy cluster.We will be Upgrading legacy clsuter from 4.2 to 7.1.3. The 7.1.3 build is happeni...

Resolved! CUCM on UCS not VMWare

I would know if I can install CUCM 8 on this platform:UCS C210 Rack Svr, 2x E5620, 6x4GB ddr 1333, 2PS, LSI1064But the installation won't be on VMWare, but the same like the older version of CUCMThanks

IP Telephony and Phones

Forum Posts

H.323 CALLING PARTY NAME

LOOKING FOR ANYBODY WITH SIP KNOWLEDGE - EASY QUESTION

2921 CME Upgrade

Intermittent reset of VoIP phones connected to Cisco 3750 switch stack

CALL WAITING "BIP" VOLUME

Resolved! Incoming calls over PRI hitting Cisco 2650 gateway, but not Mitel PBX

Implementing Teho and AAR

Resolved! Searching ip phone network

Resolved! URL

CUE 8.0.2 VM Port Upgrade

SRST - Broadcast hunt group- is it possible?

"dial-peer hunt" in CME SRST mode

Feature and design question for CME and CUE.

Resolved! CUCM 4.3 --> 7 Upgrade Utility / DMA for Parallel upgrade

Resolved! CUCM on UCS not VMWare

Meet and congratulate the February 2023 Spotlight Awardees!

Renew.cisco.com just got refreshed, and it will make your life easier!

Announcing Resources That Guide You to Success

ATA 191 CPC Settings Missing

Cisco 8851 - Transfering call to another Cisco 8851 - No ringtone

What newer model of Cisco Phones support Single Button Barge feature?

ATA 192 acknowledging with different ptime size

LSC Expiry Notification and oAuth mode

corlist configuration for outgoing calls to restrict international cal

Cisco IP phone unable to dial (787) area code number. CUCM 12.0.1 ver.

phones stopped working on ISR4331-V/K9

Convert Cisco 8841 from Enterprise to MPP as private User

Cisco VOIP 8945 Error 403: Directory Listing Denied Directory listing