Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I'm trying and failing to create custom backgrounds for my 7975 phone, I'm running unfied 6.1 and followed the these steps but I'm still unable to get my custom background to my phone.http://atc.go0se.com/?p=330When I select from my 7975 phone Settin...
FAX works fine on the ATA187, with T38. However the postage loading machine (modem), does not work on the ATA187. I use Port2 with Fax Passthrough configuration.On the PSTN gateway I have the following config:voice service voipfax protocol t38 ls-red...
2801 voice gateway pri pvdm-64.. Local callsgoing through the gateway as g711 find. Attempts to have remote phone in a region supporting g729 dead air. Call completes, you can see the phone and gateway negotiate g729 but dead air. I have transcoder...
Hi,I have a CME 8.1. I've tried to change locale to all my Ip phones. I've uploaded "CME-locale-es_ES-Spanish-7.0.1.1". Last locale for CME I've found.IPcomunicator phones have changed their locale to the Spanish one... but I'm not able to change loc...
When phone boots up it says "TFTP P00308010200.loads" and then "TFTP file not found"None of the buttons respond and I cannot get into Settings.I am able to reset it have tried that many times using this method: holding the # button while powering up ...
Our Unity subscribers all have a 10-digit extensions (eg 904-555-4444) In CallManager the phones have 10-digit DN (eg 904-555-4444), with a Translation Pattern that allows 1XXXX to expand to 904-555-XXXX. You can dial 5 digits from phone to phone and...
I have a problem similar to https://supportforums.cisco.com/message/1163554 here. I have 7937 Conference Phones which sould work with the Powercubes. For that we bought CP-7937-PWR-SPL=. We have two Phones and two splitters. The 7937s are booting wit...
Hello,i am new to IP Phones ond Callmanager ...Is it possible to show an "Icon" on the display of an 7942 if one has missed calls (maybe with the number of missed calls)?I know that i can reach the list of calls via keys on the phone. But this has t...
Hi all, how are you?I'm trying deploy the Remote Destination feature but when I click in the Mobile softkey nothing is showing.I'm using IP Communicator version 7.0.2.0 and CUCM 6.1.3.2000-1.What I can do to solve the problem?
Hi All,Sorry if i am being dumb but i currerntly have 6.0 on 2 x MCS7816H3 servers and im proposing to upgrade to CCM8.0 on 2 x new MCS7816I4 servers (i know 8.0 isnt the nest choice but i havnt got a choice on that) the thing is i presume there is a...
Hi Can any one tell me if we can have CME to use only Numeric user ids for Extension mobility. Sine in our Org. the users uses their employee id (numeric) as their login id, it is difficult to key in the user id since CME by default supports Alpha nu...
The CP-7937G IP Phone configured on out network is not powering on with power splitters and power adaptors supplied along with it. It only powers on via the POE port from a POE switch. Cisco TAC supplied all possible RMAs but none of them helped in p...
Has anyone been able to make this work? According to the BU this should install in VMWare just fine it just isn't supported which I'm ok with.Thanks,Jon
Dear AllI have a problem with a voip configuration I hope you can help with.I am trying to translate any call sent from PABX to the router on E1 0/2/1 to add the prefix 91771 or 917700. Outbound (i.e. router to PABX) the string should be sent unmodif...
I have centralized call processing and remote sites with SRST gateways. the call-manager-fallback is as follows:call-manager-fallbacksecondary-dialtone 0max-conferences 8 gain -6transfer-system full-consultip source-address 192.168.105.1 port 2000max...
