Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have a working 803 CUCM cluster and 9.03 phone firmwarephones in uk in a UK DTG and are correctly displaying BST timeHave created a new DTG for phones in another timezone applied to new DP etc, but these new phones (7942) only display UTCIf I mo...
Hi,i'm trying to register 6 E1 PRI ports of VWIC2-2MFT-T1/E1 cards. I use:- CUCM 7.1.3- 3845 Voice gateway- 3 VWIC2-2MFT-T1/E1 CardsI followed all guidelines:- i checked the right Router name and set the IP domain on both Gateway and Call Manager- C...
Platform CME/CUEI know that by default CUE will direct a call to a mailbox based on the Last Redirected number but can someone explain to me how the following will work.Call into Phone A --> fona to vm --> caller hits zero and is redirected to phone ...
I want to know if Unity 5.0 is supported on DL380-G6.I looked on documentation and it not clear.Please help..
I must be trying to reset the database password wrong. On publisher I inserted the 8.0(2c) Recovery CD. I don’t see a menu option for reset database security password. New buildout 8.0(2c), on first subscriber I’m getting a connectivity test failed...
I have a bad 2821 router that is equiped with the CF slot. What is the procedure to backup the entire config and import it into the new RMA'd 2821 router. I'm not onsite so I will have to walk someone over the phone in this process.
Hey Guys,My console's showing this error message. I have 4 PRIs on the gateway and all of them went dead when this happened. I had to reboot the router.%HWECAN-5-TIMEOUT: HWECAN in slot 0 VWIC 3 Device 1 failed to return response for Command/Query 06...
We are working to install a CME system in our UK Company and they told us at first we had ISDN line and then told us we actually had a 4 line multi auxiliary analogue line. We thought that all we needed was a VIC2-4FXO card and we would be good, but ...
Hi,i'm using CUCM 7.1.3 and i have a strange problem: when i create or configure an Intercom DN i can't select "Auto Answer Off" option because there isn't.I was reading every manual and all said that there are 3 options for configuring Intercom DN A...
hi all ,i am facing inline error on fax machine wich is connect with cisco ATA .please advice .regards
Hi,Does any one know if a VG224 using SCCP will register using only single line mode?I have a 3845 and only want VG224 ports to be single line mode to preserve ephone-dn ports and allow IP phones register using dual-line mode. This will maximize feat...
I have a Cisco 2811 that is terminating SIP trunks from my provider. From there I have FXS ports on the router that connect to a PBX. When caller call in and get the voicemail gretting they have the option to press 9 to leave a message. when they pre...
Hi,I have to get clarify couple of doubts about the IOS and 2921 Serius Router.I have one 2921 router which need to configure as CME, its came with default IOS "c2900-universalk9-mz.SPA.150-1.M2.bin" . So for configuring CME i need to download Suitab...
Hi,I have a situation where I am sending the local US calls in + E 164 (1+10 digits) format but the service provider expects to receive only 10 digits. If I send the calls to him in 11 digits we get a message that, send only 10 digits. How do we over...
Hello,I need some help to sort out an issue concerning the integration of CUE 8.0 with CUCM 8.0. I have configured the CTI ports and CTI route point in CUCM and all of them are registered.When I issue the command "show ccn status ccm-manager" in CUE,...
