Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have CUCM 7.1(3b)SU2 [7.1.3.32900-4]. It was upgrade from 7.1(3b) [7.1.3.30000-1] during installation. The subscriber has been added successfully but when I run Unified CM Cluster Overview Report it shows me a Unified CM Component Version mismatc...
I have cisco 7940's and 7960's with a 2821 router and CUCM 7.1.2. I was wondering where do the phones get the profile from in SRST mode? more specific, how do I change line appearences in SRST
Hi,I have CUCM 8.0.3 & Meeting place 8.0 in network. It is to be integrated with:-CUCM - Microsoft ADCUMC - Tandberg VCS over SIPCUCM - Microsoft OCS Meditaion server over SIP trunkMeeting place - Microsoft Exchange server.There is firewall in betwee...
Hi There !I'm having a problem with locales in the CUCM7.1.3 (just upgraded from CM4.x).I try to change the locale of the CIPC but it does not seem to recognize the change, and the softkeys stays in the same language.Only the right-click menu changes...
I have a satellite office that has reported a sporadic issue. When they receive a call it rings one time and goes to VM as they will receive the message a couple minutes later. It happens sporadically 3-4 four times a day out of 50-100 calls received...
We are converting from ISDN trunks to our Telco to SIP trunks. We already have a Cisco Call Manager cluster and already use SIP trunks. Is any additional licensing needed to convert from ISDN to telco to SIP to telco.We are installing new DS3 cards...
Recently we had our T1 go down which cares nothing but our voice traffic. We have a router/Gateway setup for SRST mode. It appears that the SRST mode failed over but it seems as though we could not make a call from our POTS line located at the office...
Hi,We would like to know if it is possible to reject incoming calls with unknow calling number. It is possible to reject incoming calls with known calling number, it is possible to reject it in the gateway, but is it possibel with an unknow calling n...
Hi everyone!I'm having this issue about having two redundant dial-peers pointing out to different IP addresses, I've setup max-conn for each dial-peer.Now my first question is if the first dial-peer is reach the max-conn, it will use the 2nd dial-pee...
When an net call is attempted through the Session Initiation Protocol (SIP) trunk, the caller gets a fast busy tone. All the incoming calls to the IP phones are fine.Any ideapls help
I have users that are getting busy signal when Dialing into Meetme Conf. I think I am hitting a limit on users, becasue some get in fine. How do I see how many users can join the conf and how many are in use during a conf.? I had a vendor help me ...
Below is an extract from one our Voice GW - Based in the UKnetwork-clock-participate slot 1network-clock-participate slot 2network-clock-participate slot 3network-clock-participate slot 4network-clock-select 1 E1 1/0/0 PABX Anetwork-clock-select 2 E1...
Hi allI have added a new JTAPI trigger in IPCCX but it shows as unregistered. I have checked the JTAPI user and the CTI RP is listed under controlled devices?Any ideas?ThanksRunning IPCCX CRS 5.0.2 and CUCM 6.1.4
I have two Cisco H323 GW interconnected with SIP. My understanding is that the allow connection statement is defining endpoints, therefore, the allow connections would be sip-sip. Is my thinking correct?
Hi,The requirement I have is for calls to a phone number to not go to voicemail during the working day but just keep on ringing, to go to voicemail after x rings between 18:00 and 20:00, and for nightservice to be used after 20:00.We have this workin...
