Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am loading a newUnity 7.x environment. I mistakingly loaded the message store piece first. wondering if this is why i cant load data store. Data stops during the setup and closes. there are no error messages to indicate why. i am at a loss. this is...
The question is how can i see if my router has the license of CUCME for 25 Seats?as example i have this new router 2911 bundle with FL-CME-SRST-25 seat license and Irun the command.. sh licenceyourname#sh license Index 1 Feature: ipbasek9 ...
We just got in a couple of 9971's with the camera's. I'm trying to get them to work no to avail. We are running CUCM 7.1.3.32900-4, which I believe supports the 9971's as I was able to configure and register the phones. The load on the phone is si...
I was trying to setup a SIP trunk using CUBE to Bandwidth.com and while it was working on inbound, with an h.323 connection to CUCM, calls were getting dropped due to the lack of a high enough CUBE version. Since I can not upgrade CUBE due to hardwa...
Hi guys,I have CUCM cluster with three nodes, three diferent devices pools and different regions, only g.711 is being used.When i start a conference using cnfr button from 7911 phone the first call stays in stand by and the new call is on, then i pre...
Deployment Scenario:-The Cisco IAD is deployed as:-Telco Network --- VoIP --- Cisco IAD2431 --- PRI to pbx at customer siteThe pbx has a lot a fax lines which are used to send faxes to one another. The customer site has multiple locations which are a...
Hi,Please my IP Phones are showing shifted time by about 9 minutes but the IP Communicatiors are reading the correct time from the NTP Server, I'm usnig CM 6.1.1.2000-3 and IP Phones: 7941G, 7975.
I have a big problem with IP Phone when I configure forward for it.On CUCM , I configure one IP phone with Noanswer External forwarding to a mobile.When I Call from PSTN to this IP Phone but no ones answer , it is going to forward the call to my mobi...
Hi All,My company is in a process of calculating the bandwidth utilization made my users calling to the conference bridge. We are using premier conference solution werein users calls in and join the bridge. We use CCM 6.3 and 2821 gatewayI need to fi...
Is there a way to speed up the upgrade installation in a production environment?In my lab, I installed 6.1(5) in the inactive partition the following order:- Publisher- TFTP - Subscriber (backup)- Subscriber (prima...
Is the 8 port pri strictly for data?
I am trying to recover a crashed CUCM that has no usable config file. How do you get Unity to act as Auto-Attendant and pick up calls to DiD's that CallManager routes?
Hi,I start to configure MGCP for fallback, but each time I try to test the fallback outside calls are getting busy signal.here the configuration :!boot system flash:c2800nm-spservicesk9-mz.124-24.T.bin!isdn switch-type primary-dms100!voice rtp send-r...
Dear sir,I am using CUCM 7.1,at the reception I have configured the hunt on 3 cisco 7965 IP Phones with 7915 expantion module,I have configured call pickup on these 3 phones,Butcall pickup is not working while Huntingso plese give me the solution for...
Hello,I hope the community can ive some good advices or/and direction of seraching the information.We're using currenty an Opensource SIP platform (Openser/kamailio + Asterisk) for switching the VoIP calls, the PSTN gateway are doing for us external ...
