Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Good day,I'm working on a CUCM4.2 with a Voice Gateway that has 2 E1 PRI ports.These two PRI ports are connected to different Telco Provider. And I want to use LCR (least cost routing).For example :I want that a called N°A goes through Port 1.When p...
Hi,We have a few problems with PCs that link via IP phones (7940/41/42's) where they don't auto-negiotiate the speed/duplex properly.I know you can hard set the S/D via the phone, but is it possible to do from CUCM?We're using 6.1.2Thanks
Hi,I need to upgrade a presence server on a new hardware from 6.x to 7.x.I have 2 questions that I couldn't figure out from the upgrade guides :1. Can I use the upgrade files downloaded from CCO ( UCSInstall_UCOS_7.0.2.10000-36.sgn.iso_part1of2 and U...
Brain cramp...what is the command that places all the commands at the beginning of the config for a 3560 that seems to define all the mls qos input and output queues? Specifically, I am talking about this stuff:mls qos srr-queue input bandwidth 90 1...
I know 'Adobe Audition' is perfect but looking a freeware for testing.Thanks in advance,
Hi,I am new enough to Cisco Ip telephony but managed to get a second FXO card configured on my Solution this morning (CME)I have some mobile pro-links and would like to have the Call Manager take all calls with a cell phone prefix and send them to sp...
A customer has an internal "First Response" capability in their plant that is called for some emergencies. The First Responders are called via the paging system.Their old phone system allowed them to press a key and use a continuous DTMF tone as an ...
Hello,I configure CUCM 7.1.(3b) everything is ok . The IP PHONE registed like 7911 7940 7960 7970 and 7942G. The matter is the ip phone 7942G and 7970 can only make an internal call . The 7942G and 7970 have On the Calling Search Space Configuration ...
Hi,I am tryin to configure SNMP on the CUCM Servicability page. I am able to add SNMP string in the Page for the CUCM servers. But when I add the SNMP destination in the Page and save it, i am unable to view the destination listed when i search for i...
Hi friends,Is there any difference between NM-HDV2-1T1/E1 and VIC2-1MFT-T1/E1 ? Can I use any of them to support E1 signaling and voice connection in all over the world ? If there is any difference, in what situation does this difference apply ?Thank...
Dear All :i have a problem with access server gateway with call manager ver. 7.0.2 , suddenly the ip phones can't do outgoing call and also the PRI can't recieve calls on it, i make work arround by changing the ip address of the gateway it worked an...
We have a problem where when we call from our desk phones (CUCM) to 3G wireless phones, the wireless phone will receive caller ID as “unknown number”. We contacted our telco/PRI provider to check the digit that we are sending and it was ok.Then we co...
HiIn Cisco Unified CCX Administration Guide, Release 8.0(1) is descriped howto setup TAPS. But this is only for CUCM 8.0 and TAPS.Where can I find the TAPS_AAR.aar file of CUCM 7.1.3?? On CUCM -> Plugins there is only an EXE-File for the old CCX vers...
I have a did line that should to ring directlt on the ip phone when somebody dial that numberplease tell me how to configure it thank youi have ccm 7 and a h232 gateway and the line is on fxo 0/0/0
I forgot my password and I'm wondering how I can submit a request to have it reset so I can access my speed dials on my Cisco IP Phone. Thank you.
