Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HiIn Cisco Unified CCX Administration Guide, Release 8.0(1) is descriped howto setup TAPS. But this is only for CUCM 8.0 and TAPS.Where can I find the TAPS_AAR.aar file of CUCM 7.1.3?? On CUCM -> Plugins there is only an EXE-File for the old CCX vers...
I have a did line that should to ring directlt on the ip phone when somebody dial that numberplease tell me how to configure it thank youi have ccm 7 and a h232 gateway and the line is on fxo 0/0/0
I forgot my password and I'm wondering how I can submit a request to have it reset so I can access my speed dials on my Cisco IP Phone. Thank you.
Hello all, Sorry for being very green. But I inherited a Cisco Unity Express phone system 2.1. We are trying to add some more phones, but are unable to getting the following error message "Registration Rejected: Max Phone". What i know so far is t...
hi All ,i had configured NTP on my CME router it was working fine for last 3 months , but now suddendly its stopped working . there is 2 min difference b/w NTP and CME router timing but date is OK . i have reconfigured but no luck . ping is working ...
hi all,i've been working on CCM 7.x, and there's something related with IPMA that doesn't seem to work. When an assistant has EM and i try to configure IPMA but i cannot select the EM DNs, only the DNs in the physical phone appears in the assistant E...
Hi to everyone,We have 3 CCMs ( one Pub and two Subs ) version 4.2(1) , we tried to upgrade to version 7.0(2) but we found a problem with DNS and we have to keep with version 4.We solve it in our lab making the upgrade without DNS.But my question is ...
We have a site with a full channelized T1 PRI - all channels in one group. The site does not seem to have a high number of calls going through but they complain that people calling are saying they are getting busy signals. I've watched the circuit ...
Hi,softkey features are not working on external calls. Features like call transfer, hold, conference etc. They are working on internal calls. The calls are from other sites which have their own CMEs and over the SIP trunk directly to this site. The g...
UCM 6.1.5 , call flow is UCM -> SIP -> ACME SBC -> Verizon Broadworks SIP -> PSTNCall is made from SCCP phone to an IVR with prompts, DTMF works. Put call on HOLD, then resume, now DTMF is no longer heard by IVR.Verizon claims the ACK after HOLD has...
Hi Experts, Would it be possible for me to extract some information from the Call Manager on a particular extension/number. What I am looking for is as follows: No. of calls on a daily basis(This I will get it from the CDR)No. of calls waiting No. of...
Hi,I am having CUCM 7.1 & MGCP gateway.User calls to reception. Reception calls to conference bridge number and transfer it to user. After transfering a call to user, user needs to enter conference password. But system is not accepting the password f...
Hi...thanks for taking the time to look at this....I have an issue where i have configured service DSAPP globally to enable hookflash for SIP to enable supplementary services for analouge phones connected off the routers FXS ports. I am running IOS ...
CM 4.2.3 SR4bI'm using the external phone number mask setting on the DN configuration of a particular phone, and I've ensured that on my route patterns Use Calling Party's External Phone Number Mask is enabled.I have an IP phone range with extension ...
I'm a registered cisco user.I'need to download the software in object.which one say where i'can find it in the Cisco web site?thanls in advancegiancarlo
