Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Good day,I have FXO trunks on a 2611XM router and have configured H323 between that gateway and a CUCM7.0 cluster which includes one publisher and one subscriber. I've configured and enabled media groups and lists, and both callmanagers service all 4...
Hi,We have CUCM 7.1 & Siemens EPBX. We have integrated CUCM with Siemens Voice gateway by H.323 and siemens voice gateway has connected to Siemens EPBX by E1.Now when Cisco IP phone calls to Siemens phone, we are not getting a ring back. But call is ...
We have one Cisco 7921G that is being used by our manager. It is connected to our Wi-Fi end point in our office. The distance range is not a problem since the phone is within the end point range.He is complaining that during a LONG conversation, s...
Hi,In my SPA8000. when I change the "Display Name" (aka: Caller ID name) found under each line configuration (L1, L2, L...etc), when making an outbound call, the Display Name seems not to be working, that is, the "Display Name" I specified is not dis...
I have ER and it is all working great exept for one user, an attendant console user, she does not recieve the voice message from Emergency Responder. Her set will ring but no voice message is there only dead air and if she does not answer the phone s...
I can't see to figure this one out. I am running CUCM 6.1.4 with CER 2.0.3. We have multiple sites, so it works like this:User in building A dials 911911 matches the extension associated with RP911, which is the CTI port that CER is usingCER matche...
I have attempted to reset the application username and password in CM 7.1.3.30000 using the command line interface command (with output):admin:utils reset_application_ui_administrator_passwordNew password:*Confirm new Password:*-------------------- u...
Assuming that there isn't any phone load name set at the device level. Do phones only load firmare when they are reset or do they check device default setting on the pub periodically for any changes? If they find a change do they load new image?
I am trying to setup a new CME System and need some help. We will be using a PRI circuit with a block of DID Numbers that are 503-652-5010 thru 5049. The location in which this is going is currently using extension 200 thru 240. They do not want to c...
How can i get PCM Capture Extraction Tool to create audio file?
I have a CME integrated with an Ancatel PBX 4400 (digital). if a call is made from a phone on the PBX to a phone on the CME, the caller information displays.But if a call is made from a phone on the CME to a phone on the PBX, the caller information d...
Hi,I`m facing an Issue where IP phones are reseting in certain Remote Locations together, What is the Best way to Diagonise this Problem.Nithin
Hello.I'd like to know how to route calls through various FXO ports in a round-robbin fashion.The default way to work is "first-available", but I have two cell-land-lines that I'd like to use in a balanced manner, because the first one is ending its ...
currenlty we have around 400 7912 IP phones in production rest is 7911 and mid series. now an issue arises few days before and that is user is facing voice jittering ang droping problem also from IPT to IPT and from PSTN. normal as well in confrence ...
Hi,Anyone seen that the installation of callmanager 7.0.1.1.11000-2 on a MCS7816H3 takes really a whole day?It seems that the installation is successfull, but come on, a whole day!!It seems to get stuck on installation database, after the normal time...
