Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,Running UCM 6.1.3.Need to upgrade the firmware load on 7961 IP Phones.Can it possible to upload the new firmware load manually in OS Administration>Managing TFTP Server Files >upload files and restart the TFTP service.Can the IP Phone able to relo...
Hello,I recently configured Offramp Gateway to place a call and activate a VXML script when the called party answers. I use the Cisco NetWorks ESMTP server to trigger a call using the following settings:EHLO CMUC01.commail From: "Grant" <76572xxxx@cm...
hi all,I have CUCM 6.1 & Cisco Presence 7.0 im not able to enable deskphone in CUPC,In cupc its showing disable & im not able to select deskphone option.Attached is the diagram which shows deskphone is not registered.can any one help me out that wher...
I have an asa between cucm and phones which is doing skinny inspect. There has been an issue where skinny setup packets are dropped, but the firewall has been retransmitting the lost packets. This has caused cucm to set up the call but there was no ...
Hi,I have UCM Cluster, 3 servers version 6.1.2.1000-13, deployed in Clustering over IP WAN model. Two servers are located in one site(publisher and subscriber 1), the third is at the remote site(subscriber 2).This configuration worked fine for more t...
Hi,I installed 7937 but not display the extension & external mask both on the LCD panel.-CUCM=7.1.3.31900-1-7937 software version=1.3(4), this is latest firmware from CCO-busy trigger=1. I found some forum suggesting to change to '2' but no luck.My e...
We have CUCM 6.1.2 and wondering the best way (and if possible) to have our receptionist to be able to call all phones, and have them pick up with speaker after she dialed a specific extension. We had this similar setup on a different phone system, ...
We are thinking of upgrading from 6.1.2 to 7.1.2. Does anyone have experiences with this (bad or good). Do we need to upgrade firmware of phones for this (7942G & 7962G). We are unning on MCS-7825-H3's. We also have Unity 7.0 and CUPS6.0.4.Any input ...
I'm wondering if anyone has ever experienced the following or has any idea what might be causing this. I have a 2821 with 2 PRI trunks into a Nortel 81c pbx. I'm using Q.sig as the switch type. The ISDN layers are up and operational. The 81c is c...
Hi, I'm trying to find out if I can reset phones using a script. I have a couple of scripts to send text messages to phones and dial but now I would like to send a reset or restart to phones.I need to know if it can be done for CM 4.1(3) or CM 7...
Is there a way to get calls received direct to mobile to be transfered to desk phone?also I have a number of users with iphones. If I install the mobile communicator client on them, is there a way to move from wifi to GSMthanks
We are setting up CUCIMOC and OCS using version 7.1 for UCM and CUCIMOC. Couple of Questions I have.Do you need the Microsoft Mediation Server? CUCIMOC will be installed for all OCS users for Call Control so is the Mediation server needed?Also for ph...
Hi all,I need to connect billing server with CUCM7, I added the server to CUCM and I am able to download the CDR file from CCM. but I have alot of problems, mainly:No information about all extensions.No information about the outgoingi calls.I am usi...
I tried to configure E1s on 3845 when I tried to add the configuration under e1 I got a message that:% Not Enough DSP servicesI checked show diag I found the PVDM on slot 0 and e1 on slot 1.I turned off the router and I moved the PVDM from slot 0 to ...
Anyway to have it embed as .MP3 insted of WAV?
