Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a Cisco 7975 phone using firmware version SCCP75.8-5-2SR1S. Cisco Call Manager version 6.1.2.1000-13.When the users places an internal or external phone call and the called party answers the phone, the call gets placed on hold and the user has...
Hi, I am trying to configure our cisco router to have any calls that originate from internal extension 37xx to use a certain dial peer and append the digits 1720 in front of any 7 digit number dialed. I opened a tac case and the config below is what ...
Has any one attempted to make the ASA phone-proxy work with CUCME 7? All the examples that I can find refer to full blown call manager and not express.I've gotten the point where a remote phone is downloading a tftp config but rather than trying con...
hi,when i make a conference call using "conf" soft key on a single line (with two incoming and two outgoing capability). the initiator (as well as the two added parties)hears the busy tone when adding third party.. i am facing the same problem when ...
I recently installed CUCM-BE 7.1.3 and have found that after adding phones that I cannot export phones with Specific details. I can look at the Job request listing as "complete, but the Job Results information is blank below the header.If I export A...
Hi,I will upgrade from CUCM 4.1.3 to 6.1.4a should i use DMA 6.1.4 or DMA 6.1.4b?ThanksBest Regards,MC
Hello,I would like to know if any of you knows what happends to a VG224 when it looses connectivity to a UCM, (this is a vg224 configured as sccp) I know the ports are actually registered with ucm, but is there a way to tell vg 224 to fallback to the...
Anyone know what PSTN technology they use to handle this? Basically, the client has a direct (no ring) line to the broker office at barclays, jpmorgan, etc. We assume the client hits a speed dial button that takes an analog off hook which direct c...
We have a non-gatekeeper controlled intercluster trunk setup between a 6.1.3 cluster (clusterA) and a 4.1.3 cluster (clusterB). The phones and the Intercluster trunks in each cluster are in separate regions and the codec between these regions are set...
Consultation, I have a CUCM 7.1 with a plan to 4-digit numeric. There is a unique three digit number, and when he dials from a VG or ATA, this call takes 15 seconds. This does not happen with the IP Phones.Any suggestions or why is this delay only wi...
Please help on more information on CME cdr records, if i open one of my cdr records that is send via gw-accounting i cannot find the info of the trunk where the call whent out on, eg. E1 or BRI. Does CME provide your dial-peer or trunk group info fo...
CME sip phone call pickup fails, after trying, searching the web, I still can't get this to work. All attempts at "call pickup" results in "reorder" displayed and heard, all phones running sip.Relevant parts of current config:!voice service voip all...
I have cisco ip phone model 7911 which static network configuration in remote site , i want to change network configuration through web access of ip phone
Hi All,Yesterday my CUCM 6.1.3 sub is crashed at 10:16 AM.We reseted it physically at 12:34 PM.I was searching in Linux logs & I found the following lines:Jan 11 12:33:56 KAUSTSUB01 kern 5 kernel: 896MB LOWMEM available.Jan 11 12:33:56 KAUSTSUB01 ker...
I have the following PolycomPhones,i want to to have them working on callmanager(ver 7.1.3).Make: Polycom IP PhoneModel: SoundStation IP 7000 SIPMake: Polycom IP PhoneModel: SoundPoint IP 650 SIPMy question is:1.Are these phone models supported on ca...
