Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Pros,I have configured MVA on CUCM 6.1 and on 2 * H.323 gateways having shared DID ISDN PRI.I am able to reach the IVR menu and authenticate via PIN.When I select 1 for making a call and enter a PSTN number or internal extension the call doesnt go...
Hi,I am trying to modify the an aa script to Call Redirect a call to a general voice mailbox. I can get it to work with one digit using Dial-by-Extension, but can't get aa to redirect a call if the digits dialed are 5555I also can't get trace informa...
Problem:Phone A is redirect to phone B.Phone B calls phone A an get a busy tone.Ok, I know there is a loop detection for the case, that phone B is redirected to phone A.But isn't there any rule like:Redirect the call exept the call comes from the pho...
I would like to confgure different ring tones for internal or external calls. Is it possible?. I use CCM 7.0Thanks.
Hello,I've upgraded my 2821 to 15.0(1)XA to try out CME 8.0. I have a SIP trunk coming in from an ITSP and everything works fine using 12.4(22)YB4. When I upgrade to 15.0(1)XA, DTMF stops working on 90% of my calls (I am forcing RTP-NTE). I have not ...
My customer asked the following Cisco Emergency Responder 7.1 questions to which I can't seem to find answers in the Cisco Web: How is data protected while on disk; is data between CER and UCUM , and between CER and the switches protected from tamper...
Hello,Wanted to find out if i upgrade my CME from its current version (flash:c2801-spservicesk9-mz.124-15.T10.bin) to version 4.3 will i loose the phone licenses in the process? I need to be able to support 7937 ip phone which the current version ca...
Hello,Wanted to find out if i upgrade my CME from its current version (flash:c2801-spservicesk9-mz.124-15.T10.bin) to version 4.3 will i loose the phone licenses in the process? I need to be able to support 7937 ip phone which the current version ca...
Hi everyone,I have a quick question about gateway/route selection in CallManager Route List. In a Route List that contains 2 H323 gateways, can an outbound call to PSTN failover to the second gateway when all the ports in the first Gateway is busy ? ...
Hi Guys,Is there a single MIB we can use to show the number of simultaneous isdn calls on 3845 and 2811 router using snmp or maybe a perl scipt?
From the ip phone I park it to 701, from the an analog phone connected to the fxs port, I dial 701. I get the hammer tone. Then I dial back the number 701 from the analog phone and its hangs the 701 until I reset it. What am I doing wrong?
Hello, everyoneI have a CUCM 7 and I am gonna to set up a external billing server , I have some questions on this setup1) the format of " directory path", for example, if my ftp server ip is 1.1.1.1, the forder is cucmcdrshould I put /cucmcdr/, or cu...
Hi,I have trouble understanding which file should be configure for a particular model.Some load such as SCCP.41..... SIP70...... are easy to understand. But some loads start with P.... are difficult.Please help,Thanks,
In CUCM 5.x when the called PSTN party is busy or switched off IP Phone is giving ring tone, please advice what I am missing in config, or it is related to E1 trunk issuse.
Hi,I have the following problems with a new communication manager 7.1.3The IP phones 7970, 7911, 7906 send the messages "Error updating locale" eventhough the local installer hasalready been loaded. The other message is " load authenication Failed".T...
