Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hi,i am configuring a SIP SRST on 3825 with CCM 6.1.3 ,and find it does not works.Could you check it for me! thanks!Here is the configurationvoice class codec 100 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729br8 cod...
We are attempting to setup a conference call on a vg224 port. We can conference in two parties, but the originator is dropped from the call. Using the hook-flash is creating a transfer and not a confrence? How do we set up a confrence on a vg224?
We have configured toll bypass on our routers and use Orion to monitor our network links. We have the routers configured as MGCP gateways. I noticed in ORION that the majority of traffic that crosses these links is RTP. No other protocol includi...
Hi NetProI have a CCME whit one E1 ti connect to PSTN, inside have a ATA186 connect to FAX, when i send FAX to ATA number the call fail.ISDN Call debug.Sep 10 16:12:36.423: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0A96 Sending Co...
Hi, I have CCM 7.0.2 with AD 2008.CCM can'T get users for default OU created by AD. I have to create other OU to fix that. Is there anything I can change in AD to let the user on ccm getting the info on ou=Users.thanks
Hi Guys,I am using CCM 5.1 and would like to meet the below requirement. When users(1000, 1001) call internally/externally to helpdesk hunt pilot(2000), the group members(3000,3001,3002) should be able to see the user extension numbers but users shou...
Hi,We have a centralized callprocessing infrastructur with a lot of branch offices, the branches have their one voicgateways to the PSTN. In only one of the branch offices we have a problem. When a call was built up the audio has a delay of 2-3 secon...
Hello All,I had a 3-PRI trunk terminated into two seperate Cisco 2851VGs working fine - in an effort to consolidate gateways we added an additional VWIC to GW#1 and terminated the 3rd PRI into it - circuits looked clean, no errors but we began having...
Hi,I have a 7845H2 with 4GB ram. I am installing the Unity bundle from Cisco. This is Windows 2003 Standard and Exchange 2003, then Unity 7. I will have 200 Unity ports (max ports). This is a standalone box with no failover and message store on box...
Hi everybody,I am just wondering whether callmanager BARS support callmanager 5.1. When I try to install BARS in the voice mail server, there is an error message that You must use cisco approved hardware to install BARS. But the voice mail server is ...
Hi all,Regarding Cisco docs:Cisco Unified Communications Manager follows the procedures that are described in RFC 3261, 3262,and 3264 to establish and clear down basic SIP calls. Often, on the outgoing side, Cisco UnifiedCommunications Manager will s...
Hello All,I am experiencing some weird behavior while implementing a standard circular hunt-group. I wonder if someone else has seen this too, and possibly has a workaround.The setup is as follows:Hunt Pilot DN 111connected with standard hunt list,co...
are those phones supported by CCME?.
I have a phone that can't get to voicemail. When hitting the message button, it rings to the correct extension but never gets to the voicemail box. It just rings and rings..Any suggestions? I'm from Avaya land and just learning the good cisco stuff.
Hi,Currently running Siemens PBX for internal Calling & PSTN.Other remote locations are connected through WAN links which are terminated on Cisco 3845 Router.We are planning to do the VOIP calls to these remote locations. In the router we added E1 ca...
