Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have been looking at adding MOH, Ring tone and a background image. I noticed that for at least one of these I need to log into the OS admin webpage. However, I was told that my login would not work for this site. What role do I need to be placed in...
Hi all,When I configure SRSRT I understand that it is an exceptional situation and therefore when a phone looses connectivity with CM and falls into SRST mode, it also looses a big part of its configuration. That is, CSS, hunt groups, pickup groups a...
I'm trying to access the Broadcast Message admin, my user have the feature to do that, but when i enter the user for the Broadcast Message admin, and then the password the system said "invalid user id or password". Im sure im using the correct user ...
Hi,I have CUCM7.0 and want to install TAPS applicaiton in UCCX5.0.2 box but I got the below error message."Error opening installation log file. Verify that the specified log file location exists and is writable"Advise please,
Hi,Have a bunch of analog wireless DECT phones that all connect back to an ASCOM box. The ASCOM connects to the LAN for connectivity back to the CUCM which is version 6.1.2.1000-1All of the DECT phones are configured as Basic 3rd party SIP devices on...
I have a DID trunk group of 4 analog groundstart trunk groups configured for wink-start signaling. Verizon now says for sure they are sending all the digits but I am not recieving them correctly, and in fact at this point am only recieving the first ...
Excuse my ignorance on the subject, but we have recently implemented a complete Cisco IP telephony solution, using Call Manager across dozens of sites. At our smaller offices, with maybe a 5-10 people, we have installed VoIP phones, connected via Cis...
Hi All,Can you please provide me the details on how to reset and reconfigure the Cisco IP Phone 7960G.
I have a hunt pilot forwarding to a supervisor phone after 10 seconds of RNA. Problem is that if the Sup isnt sitting at his phone the call doesnt go straight to his voicemail box. It just goes to unity and prompts the caller to enter the mailbox num...
hi,i have many client with cisco call manager express 7.0.1i copy the CME-locale-fr_FR-French-7.0.1.1.tar in flash:its/i execute the commande in telephony-service:user-locale FR load CME-locale-fr_FR-French-7.0.1.1.tar.i created ephone-template with ...
Hello,I have a problem on CCM 5.1.2. I can do the administration via web gui but no changes are really applied. E.g. I change DN on the phone, reset the phone everything looks fine on CCM but phone stays with the old DN. I delete the phone , and it i...
HelloI have a little problem with our CM 4.1(3)sr8a, OS 2000.2.7 with Upgrade to 2000.4.5a and OS Service Release 2000.4.5bSR5.I like to monitor the number of registered phones, cpu usage, memory usage etc. with the RTMT.I don't know why, but it does...
Hi There, this issue is causing me much frustration. We are running CUCM 6.1 and a 3845 ISR running advipsvcs 124-15.T8 IOS. Basically, outbound calls are not matching the specific dialpeers that I have configured on the H323 Gateway. We also have...
Dear All,I have implemented CUCM 6.1 with MGCP gateway...just need to clear one thing that is somebody told me that Call ID is not supported with MGCP gateway but it works fine with H.323 gateway...currently i am not able to see calling party number ...
In general with a Verizon Buisness SIP Trunk is a MTP resource required for every call? So planning for 80 calls means you should have 80 hardware IOS MTP resources avail? We noticed without MTP resources we can't transfer calls. Using CallManager...
