Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
helloI have on central and 3 remote site with VPN IPSec Router-to-Router Hub and spokeCME ---> central router--->remote routerall ip address is privatecentral and remotes sites are connected by 3 wireless linkI configued ipsec vpn betweencentral rout...
I have recieved approx 20 tickets today for internal users attempting to make outbound calls. We have 2 full PRIs for outbound voice and don't appear to have a capacity issue. Looking at the CDR for each failed call, they contain a destCause_value of...
Hi, i'am planning to upgrade unity from 2.x to 7.x;as the exchange server is upgraded to 2007 , and is not supported by unity 2.xis there any way for 2.x to support exchange 2007. Thank you.
We are ordering a standard isdn pri (23 B + 1 B). Our telco allows us to specify that all channels are In/Out (DID/DOD), but that we can limit the max number of DID/DOD. In other words, if we always want to make sure there are 3 channels for outgoi...
Without sending me to a Cisco Link to the 7921 phone can someone tell me how to unlock the keys so I can make changes on a phone please?
I need to make changes to a few ephones such as username and number, but the GUI will not allow this. Is there a way through command line interface?
I have a lab with a CCM 4.3 and 2821 VG running IOS 12.4(13r). We dont have a PRI to pull to the T1 controller so I'm testing dial tone with the VIC2-4FXO card. I've pulled 2 POTS lines to the FXO ports and have configured their endpoints in CCM with...
Hi AllI want to upgrade my cucm 6.1(2) to 6.1(3) i have downloaded two very large files with .iso_part1of2 extensions. Do i need to remove the extension from the file and leave just .iso ?i looked for support documentation but cant find anything usef...
Can someone please give me an example of when you would want to use the ISDN Network-Specific Facilities Information Elements in a route pattern? I would think all ISDN settings would be done on the gateway. Obviously I am missing something or I am...
I've followed the CER 7 installation as a new publisher.Now that the installation is done is showing a DOS screen with a loginI've already login as administrator but i'm not sure what to do.Is there any GUI interface?We just purchased CER and we are ...
What are the differences between these 2 cards. And in what scenarios would you use one or the other.
Hi,<br /><br />I just get a brand new cisco 2801 and a VIC2-2FXS that I install in the slot 0 (VIC only).<br /><br />I can see my card in the sh diag and sh ver but the voice ports never appear on the sh run. I can't type voice-port either...<br /><b...
Hello,We are having an issue. that being we have a third party, MTS, collecting CDR data. When calls come in to our operator, she transfers the call to a hunt group. but all that shows in the data being output from CM is the hunt group number, not th...
Hi netpro's - easy question.I am upgrading CCM 4.1.3 to UCM 7.x and have about 800 phones on our network. Is it easier to stick with the DHCP ooption on the new UCM box, or should I go with local DHCP distrabuted from switches/routers at each of my 9...
Hi, i have an issue with a MGCP Gateway configuration (2851/IOS 12.4-23) connected to a CUCM 6.1.2.when i dial a number, as soon as the number match a unique route pattern, the call is send over the E1 and the operator send back an error as the numbe...
