Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a new deployment with RightFax 9.3 and Callmanager 6.1. The gateway is a CMM module off of a 6509 and it uses MGCP to communicate with the CUCM. An ICT is setup between CUCM and the RightFax server. I set up a RP to point incoming DID calls...
I need to use TAPS for a roll out but unlike 4.x which I`ve used it on before, TAPS is windows and CUCM is not- Has any one used TAP`s in a 6.X rollout and how. Do I need to install a new Cisco Windows server and point the CTI RP to it. On 4.x, I ...
Hello again after a while.I wrote this TCL/IVR script that will call you back provided that your calling number is pre-configured in a list of ANIs. You will then receive dialtone and be able to place further unlimited calls.The way to use it, is to ...
Dear FriendsI have an issue with my ip phones, i want all the phones (5) to ring when the call lends at the router. can any one please help me with this, the system is working fine just wanna resolved the above issue. There are four 7912 phone and on...
Hi,Is it possible to copy/paste in an excel doc or generate a csv file when you do a search of devices registered in CUCM ?Results of devices registered can't be exploited and impossible to generate a report with such details.Thanks in advance
Hy Guys,My Customer have a CallManager version 3.1.3a with 15G of HD and need space avalaible. I delete the files in CDR but the space is short and didn't solve the problem. It's possible delete anothers files thing to have more space in the HD?Thank...
I have an open TAC case on this, but so far they aren't being very helpful. So I'm hoping someone here might have some suggestions.Basically, we upgraded from CM6 to CM7 and no phone will register. They displaying "registration rejected" (no message ...
How should the setup be to get the SIP trunk working? I have only used BRI or PRI before so I have no clue, please help me!I need some sample configuration on the dial-peer and everthing.
Looking for some documentation on how I could go about implementing QSIG with an Avaya PBX. Any info would be great.
Hi,I have a question, how to program a key on ip phone 7970? There are some button near the screen and I want to program a specific key to dial a number.For example if I press this button I dial the number 100
Hi all,I am building route patterns for International calls. I have tried to find the definition of a DDI, but have been unsuccessful in my search.The DDI is: PreDot IntlAccess IntlDirectDialWhat does this particular DDI do?Also, What does the Intl...
I have a sip dial-peer with destination-pattern 521T sending calls to a GSM gateway (QUESCOM). the normal calls are working prefectly, but when i tried to call 521*333 for example, the GSM gateway only receives 521 in other words the cisco gateway is...
Hi all,I have some questions about such type of integration: 1. terminology : when we say H323 does this mean necessarily an IP PABX or an hybrid PABx ?2. In case that we are about integrating a CCM V7.0 CCM with an another IP PABX (an other mark, I ...
Hi all,I am new with IPCC Express 5.0 (CRS 5.0).I need to know with which Database type CRS 5.0 is compatiblie with?Is PostgreSQL supported by IPCCX 5.0 ? if not whic other DBs that can be supported?Please i need urgent help Thanks in advance.
Hi Guys, My Customer have a solution with CCM version 5.1. Actually the Customer have in the Matriz 02 gateway of Carrier different. He is using Gateway 01 only receive the Calls (In) and Gateway 02 to do and receive (In and Out). Now he need change ...
