Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,This installation is CUCM 11.5 with SIP trunk to CUBE then to ITSP. CUCM->CUBE is delayed offer, everything else is EO. CUBE has a transcoder registered with CUCM and included in MRGL of both trunk and phone. In general this doesn't get used ...
Hi, I have configured the Cisco phone 7821 and can't register on CUCM. The phone is getting Sign-in Service Domain, User ID and Password once connected to the network. When tried the credentials, the error is "Please check your information and try a...
Hi Guys,I'm pretty new to CUCM and SIP, so please go easy on me.I'm having some difficulty with Outbound calls, in that I get a SIP 404 Not Found error from CUCM after the invite request. Inbound calls are working fine so I'm pretty confident it's so...
Hi,I am trying to configure an FXO port on a router but the comand "voice-port" is not accepted. Is the command 'voice-port" supported on a cisco 2811 router?
Hello, Please i need help, Actually i have a cisco phone 3905, I need to load the firmware into in my router (telephony-service). I've tried to upload a tar file but i can't find my phone in the list when doing "Load?" command. Somebody help please....
Greetings Everyone, I am trying to implement SIP trunk thru our current data circuit with below call flow. I was able to get the SIP registration with SIP carrier and when I make a inbound call from my cell phone to one of the SIP carrier provided DI...
System version: 11.5.1.10000-6 We have configured AD-Hoc conference as well as conference now feature. While using AD-Hoc conference feature we are able to see the conference list but not in Conference now.. Using Cisco 8851. Is there any provisio...
Hi, I have a customer who want to use existing Cisco phones on an Alcatel IP-PABX. In order to use these Cisco IP phones on, they would need to be converted to SIP mode. I have the phone models and the current firmware attached. Can you confirm if th...
Hi All I have a problem.I have a CUCM 11 and H323 PRI E1. For outgoing call, the follow message is show it: Requested circuit/channel not availableHere a ISDN Q931 debugSep 5 14:33:37.771: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x3470 ...
I'm looking for end user training videos for Cisco CP-8841 IP phone, I cannot find them anywhere on the site. Can someone point me in the right direction. J
Hi Team, We are already having Cisco CME ruuning on Cisco 3900 ISR routers and want to add additional CUE module on this router. How can i assure whether additional hardware can be placed on same router or not.
Our call back feature relies on the agent to press "any digit" to place the call back to the customer. Pending call backs are presented in our queue as calls waiting, by design there is no way for the agent to differentiate a live call that is wai...
Hi,I would like to assign two PSTN numbers to be called from a specific DN.For Example, DN = 112 should only make calls to following numbers only.+256700400100+256700400101 Thanks in Advance,Nooruddin
Dear Community, I have configured three CSS. HQ-EXEC(international,national and internal),HQ-EMP(national and internal),HQ-OPENAREA(internal). HQ-EXEC can call all extensions but cannot receive calls from HQ-EMP and HQ-OPENAREA. HQ-EMP can call HQ-OP...
Hi, I have a fresh install of 10.5 but when attempting self provision im getting error 'This Device Cannot Be Associated to your account, contact your systems administrator' Been using doco, could be missing something in my config.http://www.cisco.c...
