Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Some employees do not have permanent desks but require DN assigned for each mobility user. These people will use virtual desk (aka host desk) office space.CCM 4.1(3) can you create a user and assign a DN without device configuration?thanks in advance...
We are considering using IPMA, however the single route point is an issue. We could have Manager's DNs (which can't change) which could be anywhere in the XXXX range, but we already have a route pattern for XXXX which routes non-IP destinations towar...
Is there a way to override a call forward all, for example if someone has a DN forwarded to them, they receive a call to that DN, they know that the person is at the desk, and they want to push to call back to them or let them know they are on forwar...
Hi,I have seen a video of Unity Audio Text Manager that shows features (like the "references to this object" windows) that are not available in the version of Audio Text Manager that we use (5.0 build 24). I have checked on the Cisco Unity Tools web ...
We are using Call Manager 6 and we are using Active Directory. We have synced with AD and we have a user which has been deleted. It shows up as inactive in Call Manager and has been this way for 5 days. How do we get it to disappear all together f...
Hello,I'm not able to transfer a call with consultation to an analog phone connected to an ATA.Only way to transfer the call is using blind mode without consultation.I think my 2801 with CME is correctly configurated.I set the telephony-service 'tran...
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008084fe1f.shtmlSoftware MTPs are supported on the router only if the dsp services dspfarm command is not enabled on the voice card.I thought software MTP actual...
Hi,We want to block user to call 900 number, play a record message if user try to dial 900. I know annunciator can do this. Someone know how to configure CM to do it.
Hi,I am having disconnection problem with FXO after remote party disconnects the call. Fxo port not going to onhook state. Please find below my configuration on the Voice-port.*****************************************voice-port 0/1/1 translation-prof...
The VWIC-2MFT-T1-DI is a drop/insert module for CAS but can it also support PRI as per below:Can a VWIC-2MFT-T1-DI= support MGCP with Primary-NI to Callmanager 4.2.3sr1?I have the following in my 3725.c3725-advipservicesk9-mz.124-8a.bin with 128F/256...
Hi All,I have a configuration problems with a new CCME system: router 2811 (firmware: 12.4.15T1 + n. 23 IP Phone 7931G firmware: SCCP31.8-2-2SR1S.The problem is during transfer call from a internal number e.g. 101 and another internal number e.g. 10...
Hi Friend, is it possible to configure dtmf tone on ata? if yes how can i configure it?
I have two cell providers and able to dial from CCM successfully but there is different ISDN call processing. one receiving 'alert' when the other 'progress' command.why different command receiving and/or any violation the ISDN standard?carrier#1----...
Phone keeps requesting SEPDefault.cnf, SEP<mac_address>.com and XMLDefault.cnf.xml. What changes are required for the phone to request SIPDefault.cnf & SIP<mac_address>.cnf etc.?thanks in advanceAjaz
Hi,I have CCME 4.1 with CUE 2.3 i reset the web administrator password based on the following documenthttp://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_password_recovery09186a008042aa29.shtmlI was able to authenticate at the main page of...
