Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am replacing a SPE 310 in a ICS 7500 Chassis because the hard drive is going out on the old system. Does anyone know where I can find the Product Key information asked for during Call Manager Installation on the new server on the old server?
Hi team, does any body know that how can I access the voice mail configured for ephone hunt group.I have a hunt group number 1001 with three number 1002, 1003, 1004 and final numbe is 1000 which is voice mail pilot.ephone-hunt 1 sequentialpilot 1001l...
Our event viewer is getting flooded with the following errors. DCOM got error"Logon failure: user account restriction. "and was unable to logon \WAM_Guest in order to fun the server. The other error which follows isThe server failed to load applicati...
Hello,I've set up a hunt group (sucessfully tested by hitting pilot extension). I would like to have that extension accessible by dialing it at the Unity Auto Attendant. Besides setting up a voicemail box for it, how else can I configure this?-Shik...
I am trying to install the Exchange 2003 System Management Tools on a server MCS-7825-H2-ECS1 server that is running Windows 2003. I used the Unity Platform Configuration Discs that came with the server to load the OS. When I get to the part to ins...
I am testing IP communicator v2.0 with call manager v4.0(2a)sr2c. Most of the ipt communicator functions and voice quality are working well in the office LAN. Except, there is no MOH when remote calling party puts (ipt phone model 7940)the call to...
Hi,i have ccm4.1.3 with cisco 7900 series ip phones. Have a small query, if I can have some sort of messages/ screensaver shown in the display of these ip phones. The message can be a blinking one or screensaver type on the background.Need help in ge...
Hi,I'm trying to configure CME(4.0).When user dials to PSTN, IPPhone displays manipulated number instead of the actual number dialed.I want to display original dialed number on IPPhone and I have to configure CME to select PSTN line.If you have any s...
Is there a reason why Cisco don't have the Canadian French locale?I know the user locale only affect the phone display and some system prompts. Some one told me the France French and Canadian French are very different and there are some historical/po...
hi i have a 2811 cisco router with fxo card and 12.4 advance enterprise IOS i have no voice-port commandi have just voice-card !!help me
How h323 will be handle 2xPRI with DID attached to different routers in case all 24 channels are taken?Basically, if the voice gateways are setup has H.323, and we place PRIs on each router. How can I configure CCM for outbound calls to *both* ro...
I understand that when deploying a CCM cluster the Publisher must built first.Does it also have to be attached to the network before commencing with Subsciber build?. Cannnot seem to find the document at the momment expaining the prerequisites and pr...
I am configuring an H323 PRI gateway in CCM, which connects to a third party's PBX. I would like to designate the CCM gateway as the "Network" side of the PRI, and the other vendors PBX as "User".How can I specify the Network function on the CCM sid...
Hi, I'm having a bit of trouble here with the port speed on a few phones. It doesn't seem to matter which type of phone I use, 7911 or 7941. I have any area, All on the same VLAN, All points going to the same switch. When I connect a phone through...
HiCM4.2.3sr1 with UM4.2.1pstn calls 1000 which does a CFAll to 2000 which does a CFBusy/CFNoAnswer to VM but it always reaches 1000 VM. I want it to reach 2000 VM.Unity's CallViewer always show 1000 as the forwarding DN.I've tried:1. Putting TP to ch...
